PROTOCOL

This documents OpenSSH's deviations and extensions to the published SSH
protocol.

Note that OpenSSH's sftp and sftp-server implement revision 3 of the SSH
filexfer protocol described in:

http://www.openssh.com/txt/draft-ietf-secsh-filexfer-02.txt

Newer versions of the draft will not be supported, though some features
are individually implemented as extensions described below.

The protocol used by OpenSSH's ssh-agent is described in the file
PROTOCOL.agent

1. Transport protocol changes

1.1. transport: Protocol 2 MAC algorithm "umac-64@openssh.com"

This is a new transport-layer MAC method using the UMAC algorithm
(rfc4418). This method is identical to the "umac-64" method documented
in:

http://www.openssh.com/txt/draft-miller-secsh-umac-01.txt

1.2. transport: Protocol 2 compression algorithm "zlib@openssh.com"

This transport-layer compression method uses the zlib compression
algorithm (identical to the "zlib" method in rfc4253), but delays the
start of compression until after authentication has completed. This
avoids exposing compression code to attacks from unauthenticated users.

The method is documented in:

http://www.openssh.com/txt/draft-miller-secsh-compression-delayed-00.txt

1.3. transport: New public key algorithms "ssh-rsa-cert-v00@openssh.com",
     "ssh-dsa-cert-v00@openssh.com",
     "ecdsa-sha2-nistp256-cert-v01@openssh.com",
     "ecdsa-sha2-nistp384-cert-v01@openssh.com" and
     "ecdsa-sha2-nistp521-cert-v01@openssh.com"

OpenSSH introduces new public key algorithms to support certificate
authentication for users and hostkeys. These methods are documented in
the file PROTOCOL.certkeys

1.4. transport: Elliptic Curve cryptography

OpenSSH supports ECC key exchange and public key authentication as
specified in RFC5656. Only the ecdsa-sha2-nistp256, ecdsa-sha2-nistp384
and ecdsa-sha2-nistp521 curves over GF(p) are supported. Elliptic
curve points encoded using point compression are NOT accepted or
generated.

1.5 transport: Protocol 2 Encrypt-then-MAC MAC algorithms

OpenSSH supports MAC algorithms, whose names contain "-etm", that
perform the calculations in a different order to that defined in RFC
4253. These variants use the so-called "encrypt then MAC" ordering,
calculating the MAC over the packet ciphertext rather than the
plaintext. This ordering closes a security flaw in the SSH transport
protocol, where decryption of unauthenticated ciphertext provided a
"decryption oracle" that could, in conjunction with cipher flaws, reveal
session plaintext.

Specifically, the "-etm" MAC algorithms modify the transport protocol
to calculate the MAC over the packet ciphertext and to send the packet
length unencrypted. This is necessary for the transport to obtain the
length of the packet and location of the MAC tag so that it may be
verified without decrypting unauthenticated data.

As such, the MAC covers:

      mac = MAC(key, sequence_number || encrypted_packet)

where "encrypted_packet" contains:

      byte      padding_length
      byte[n1]  payload; n1 = packet_length - padding_length - 1
      byte[n2]  random padding; n2 = padding_length

2. Connection protocol changes

2.1. connection: Channel write close extension "eow@openssh.com"

The SSH connection protocol (rfc4254) provides the SSH_MSG_CHANNEL_EOF
message to allow an endpoint to signal its peer that it will send no
more data over a channel. Unfortunately, there is no symmetric way for
an endpoint to request that its peer should cease sending data to it
while still keeping the channel open for the endpoint to send data to
the peer.

This is desirable, since it saves the transmission of data that would
otherwise need to be discarded and it allows an endpoint to signal local
processes of the condition, e.g. by closing the corresponding file
descriptor.

OpenSSH implements a channel extension message to perform this
signalling: "eow@openssh.com" (End Of Write). This message is sent by
an endpoint when the local output of a session channel is closed or
experiences a write error. The message is formatted as follows:

	byte		SSH_MSG_CHANNEL_REQUEST
	uint32		recipient channel
	string		"eow@openssh.com"
	boolean		FALSE

On receiving this message, the peer SHOULD cease sending data of
the channel and MAY signal the process from which the channel data
originates (e.g. by closing its read file descriptor).

As with the symmetric SSH_MSG_CHANNEL_EOF message, the channel does
remain open after a "eow@openssh.com" has been sent and more data may
still be sent in the other direction. This message does not consume
window space and may be sent even if no window space is available.

NB. due to certain broken SSH implementations aborting upon receipt
of this message (in contravention of RFC4254 section 5.4), this
message is only sent to OpenSSH peers (identified by banner).
Other SSH implementations may be whitelisted to receive this message
upon request.

2.2. connection: disallow additional sessions extension
     "no-more-sessions@openssh.com"

Most SSH connections will only ever request a single session, but a
attacker may abuse a running ssh client to surreptitiously open
additional sessions under their control. OpenSSH provides a global
request "no-more-sessions@openssh.com" to mitigate this attack.

When an OpenSSH client expects that it will never open another session
(i.e. it has been started with connection multiplexing disabled), it
will send the following global request:

	byte		SSH_MSG_GLOBAL_REQUEST
	string		"no-more-sessions@openssh.com"
	char		want-reply

On receipt of such a message, an OpenSSH server will refuse to open
future channels of type "session" and instead immediately abort the
connection.

Note that this is not a general defence against compromised clients
(that is impossible), but it thwarts a simple attack.

NB. due to certain broken SSH implementations aborting upon receipt
of this message, the no-more-sessions request is only sent to OpenSSH
servers (identified by banner). Other SSH implementations may be
whitelisted to receive this message upon request.

2.3. connection: Tunnel forward extension "tun@openssh.com"

OpenSSH supports layer 2 and layer 3 tunnelling via the "tun@openssh.com"
channel type. This channel type supports forwarding of network packets
with datagram boundaries intact between endpoints equipped with 
interfaces like the BSD tun(4) device. Tunnel forwarding channels are
requested by the client with the following packet:

	byte		SSH_MSG_CHANNEL_OPEN
	string		"tun@openssh.com"
	uint32		sender channel
	uint32		initial window size
	uint32		maximum packet size
	uint32		tunnel mode
	uint32		remote unit number

The "tunnel mode" parameter specifies whether the tunnel should forward
layer 2 frames or layer 3 packets. It may take one of the following values:

	SSH_TUNMODE_POINTOPOINT  1		/* layer 3 packets */
	SSH_TUNMODE_ETHERNET     2		/* layer 2 frames */

The "tunnel unit number" specifies the remote interface number, or may
be 0x7fffffff to allow the server to automatically chose an interface. A
server that is not willing to open a client-specified unit should refuse
the request with a SSH_MSG_CHANNEL_OPEN_FAILURE error. On successful
open, the server should reply with SSH_MSG_CHANNEL_OPEN_SUCCESS.

Once established the client and server may exchange packet or frames
over the tunnel channel by encapsulating them in SSH protocol strings
and sending them as channel data. This ensures that packet boundaries
are kept intact. Specifically, packets are transmitted using normal
SSH_MSG_CHANNEL_DATA packets:

	byte		SSH_MSG_CHANNEL_DATA
	uint32		recipient channel
	string		data

The contents of the "data" field for layer 3 packets is:

	uint32			packet length
	uint32			address family
	byte[packet length - 4]	packet data

The "address family" field identifies the type of packet in the message.
It may be one of:

	SSH_TUN_AF_INET		2		/* IPv4 */
	SSH_TUN_AF_INET6	24		/* IPv6 */

The "packet data" field consists of the IPv4/IPv6 datagram itself
without any link layer header.

The contents of the "data" field for layer 2 packets is:

	uint32			packet length
	byte[packet length]	frame

The "frame" field contains an IEEE 802.3 Ethernet frame, including
header.

3. SFTP protocol changes

3.1. sftp: Reversal of arguments to SSH_FXP_SYMLINK

When OpenSSH's sftp-server was implemented, the order of the arguments
to the SSH_FXP_SYMLINK method was inadvertently reversed. Unfortunately,
the reversal was not noticed until the server was widely deployed. Since
fixing this to follow the specification would cause incompatibility, the
current order was retained. For correct operation, clients should send
SSH_FXP_SYMLINK as follows:

	uint32		id
	string		targetpath
	string		linkpath

3.2. sftp: Server extension announcement in SSH_FXP_VERSION

OpenSSH's sftp-server lists the extensions it supports using the
standard extension announcement mechanism in the SSH_FXP_VERSION server
hello packet:

	uint32		3		/* protocol version */
	string		ext1-name
	string		ext1-version
	string		ext2-name
	string		ext2-version
	...
	string		extN-name
	string		extN-version

Each extension reports its integer version number as an ASCII encoded
string, e.g. "1". The version will be incremented if the extension is
ever changed in an incompatible way. The server MAY advertise the same
extension with multiple versions (though this is unlikely). Clients MUST
check the version number before attempting to use the extension.

3.3. sftp: Extension request "posix-rename@openssh.com"

This operation provides a rename operation with POSIX semantics, which
are different to those provided by the standard SSH_FXP_RENAME in
draft-ietf-secsh-filexfer-02.txt. This request is implemented as a
SSH_FXP_EXTENDED request with the following format:

	uint32		id
	string		"posix-rename@openssh.com"
	string		oldpath
	string		newpath

On receiving this request the server will perform the POSIX operation
rename(oldpath, newpath) and will respond with a SSH_FXP_STATUS message.
This extension is advertised in the SSH_FXP_VERSION hello with version
"1".

3.4. sftp: Extension requests "statvfs@openssh.com" and
         "fstatvfs@openssh.com"

These requests correspond to the statvfs and fstatvfs POSIX system
interfaces. The "statvfs@openssh.com" request operates on an explicit
pathname, and is formatted as follows:

	uint32		id
	string		"statvfs@openssh.com"
	string		path

The "fstatvfs@openssh.com" operates on an open file handle:

	uint32		id
	string		"fstatvfs@openssh.com"
	string		handle

These requests return a SSH_FXP_STATUS reply on failure. On success they
return the following SSH_FXP_EXTENDED_REPLY reply:

	uint32		id
	uint64		f_bsize		/* file system block size */
	uint64		f_frsize	/* fundamental fs block size */
	uint64		f_blocks	/* number of blocks (unit f_frsize) */
	uint64		f_bfree		/* free blocks in file system */
	uint64		f_bavail	/* free blocks for non-root */
	uint64		f_files		/* total file inodes */
	uint64		f_ffree		/* free file inodes */
	uint64		f_favail	/* free file inodes for to non-root */
	uint64		f_fsid		/* file system id */
	uint64		f_flag		/* bit mask of f_flag values */
	uint64		f_namemax	/* maximum filename length */

The values of the f_flag bitmask are as follows:

	#define SSH_FXE_STATVFS_ST_RDONLY	0x1	/* read-only */
	#define SSH_FXE_STATVFS_ST_NOSUID	0x2	/* no setuid */

Both the "statvfs@openssh.com" and "fstatvfs@openssh.com" extensions are
advertised in the SSH_FXP_VERSION hello with version "2".

10. sftp: Extension request "hardlink@openssh.com"

This request is for creating a hard link to a regular file. This
request is implemented as a SSH_FXP_EXTENDED request with the
following format:

	uint32		id
	string		"hardlink@openssh.com"
	string		oldpath
	string		newpath

On receiving this request the server will perform the operation
link(oldpath, newpath) and will respond with a SSH_FXP_STATUS message.
This extension is advertised in the SSH_FXP_VERSION hello with version
"1".

$OpenBSD: PROTOCOL,v 1.18 2012/12/11 22:31:18 markus Exp $