docs/nload.1.in

.\"
.\" Man page for nload
.\" Copyright (C) 2001 - 2003 by Roland Riegel <feedback@roland.riegel.de>
.\"
.TH nload 1 "December 07, 2003" nload "Network monitoring tools"
.SH NAME
nload \- displays the current network usage

.SH SYNOPSIS
.B nload
.RB [ \-i
.IR max_scaling ]
.RB [ \-m ]
.RB [ \-o
.IR max_scaling ]
.RB [ \-s
.IR smoothness ]
.RB [ \-t
.IR interval ]
.RB [ \-u
.IR h|H|b|B|k|K|m|M|g|G ]
.RB [ \-U
.IR h|H|b|B|k|K|m|M|g|G ]
.RI [ devices ]

.B nload \-\-help|\-h

.SH DESCRIPTION
.B nload
is a console application which monitors network traffic and bandwidth usage in real time.
It visualizes the in- and outgoing traffic using two graphs and provides additional info
like the total amount of transfered data and min/max network usage.

.SH USAGE
When running
.B nload,
you can switch between the devices (which you gave
.B nload
on the command line) by pressing the left and right arrow keys. If the
.B \-m
command line parameter is given, the arrow keys switch as many devices back and forth as
there are shown on the screen. If you want to quit, do so by pressing 'q' or 'Ctrl+C'.

For further key shortcuts, have a look at the sections
.B MAIN WINDOW
and
.B OPTION WINDOW
below.

.SH OPTIONS
A summary of the options supported by
.B nload
is included below.

.TP
.B \-i max_scaling
Specifies the 100% mark in kBit/s of the graph indicating the incoming bandwidth usage.
Ignored if max_scaling is 0 or the switch -m is given. The default value for max_scaling
is 10240.
.TP
.B \-m
Show multiple devices at a time; do not show the traffic graphs.
.TP
.B \-o max_scaling
Same as -i but for the graph indicating the outgoing bandwidth usage.
.TP
.B \-s smoothness
Sets the "smoothness" of the average in/out values.
A value of 1 means little smoothness (average over a short period of time), a value of 9
means high smoothness (average over a long period of time). The default is 9.
.TP
.B \-t interval
Determines the refresh interval of the display in milliseconds.
If interval is 0 print net load once and exit.
The default value of interval is 500.

PLEASE NOTE:
Specifying refresh intervals shorter than about 200 milliseconds makes traffic
calculation very unprecise. Also the display may flicker using such short
refresh intervals.
.B nload
tries to balance this out by doing extra time measurements, but this may
not always succeed.
.TP
.B \-u h|H|b|B|k|K|m|M|g|G
Sets the type of unit used for the display of traffic numbers.
h means human readable (auto), b Bit/s, k kBit/s, m MBit/s and g GBit/s.
The upper case letters mean the corresponding units in Bytes (instead of Bits).
The default is k.
.TP
.B \-U h|H|b|B|k|K|m|M|g|G
Same as -u, but for an amount of data, e.g. Bit, kByte, GBit etc. (without "/s").
The default is M.
.TP
.B devices
Network devices to use. The default device is "eth0" on Linux, "fxp0" on
BSD, "hme0" on Solaris and "lan0" on HP-UX.
.TP
.B \-h, \-\-help
Show a short summary of these command line options.

.SH MAIN WINDOW
After starting,
.B nload
begins to monitor the network devices given on the
command line, or, if none where specified, the default device. In this mode,
the following key shortcuts are available.

.TP
.B 'o'
Show the option window (see section 
.B OPTION WINDOW
below).

.TP
.B 'ArrowRight', 'ArrowDown', 'PageDown', 'Enter', 'Tab', 'n'
Switch the display to the next network device, or, when started with the
.B \-m
flag, to the next page of devices.

.TP
.B 'ArrowLeft', 'ArrowUp', 'PageUp', 'p'
Switch the display to the previous network device, or, when started with
the
.B \-m
flag, to the previous page of devices.

.TP
.B 'q', 'Ctrl+C'
Quit
.BR nload .

.SH OPTION WINDOW
The parameters given to
.B nload
on the command line can be adjusted during run time by pressing the 'o' key. A
small window appears on the top of the screen, listing the available settings.

.TP
.B 'o'
Show/hide the option window.

.TP
.B 'ArrowLeft', 'ArrowRight', 'Home', 'End'
Navigate within the edit fields.

.TP
.B 'ArrowUp', 'ArrowDown', 'Enter'
Navigate between the settings.

.TP
.B 'PageUp', 'PageDown', 'Tab'
Toggle between the different values possible for the current field.

.TP
.B '+', 'n' / '-', 'p'
Switch to the next / previous page of settings.

.SH FILES
.I /proc/net/dev
is read by
.B nload
when running on Linux to get the network traffic data.

.SH VERSION
This manual page describes version @VERSION@ of
.BR nload .

For updates, look at the nload homepage:
.br
.B http://www.roland-riegel.de/nload/index_en.html

.SH HELP
If you need help, either contact me directly (see below) or write to the
nload-user mailing list at
.br
.B nload-user@lists.sourceforge.net
.br
after having subscribed at
.br
.BR https://lists.sourceforge.net/lists/listinfo/nload-user .

.SH AUTHOR
Copyright (C) 2001 - 2003 Roland Riegel <feedback@roland-riegel.de>

This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.

This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.