blob: 7771473c02548b7e816fd63c24c16392e2ee92e8 [file] [log] [blame] [raw]
/* rtl8139.c - etherboot driver for the Realtek 8139 chipset
ported from the linux driver written by Donald Becker
by Rainer Bawidamann (Rainer.Bawidamann@informatik.uni-ulm.de) 1999
This software may be used and distributed according to the terms
of the GNU Public License, incorporated herein by reference.
changes to the original driver:
- removed support for interrupts, switching to polling mode (yuck!)
- removed support for the 8129 chip (external MII)
*/
/*********************************************************************/
/* Revision History */
/*********************************************************************/
/*
4 Feb 2000 espenlaub@informatik.uni-ulm.de (Klaus Espenlaub)
Shuffled things around, removed the leftovers from the 8129 support
that was in the Linux driver and added a bit more 8139 definitions.
Moved the 8K receive buffer to a fixed, available address outside the
0x98000-0x9ffff range. This is a bit of a hack, but currently the only
way to make room for the Etherboot features that need substantial amounts
of code like the ANSI console support. Currently the buffer is just below
0x10000, so this even conforms to the tagged boot image specification,
which reserves the ranges 0x00000-0x10000 and 0x98000-0xA0000. My
interpretation of this "reserved" is that Etherboot may do whatever it
likes, as long as its environment is kept intact (like the BIOS
variables). Hopefully fixed rtl_poll() once and for all. The symptoms
were that if Etherboot was left at the boot menu for several minutes, the
first eth_poll failed. Seems like I am the only person who does this.
First of all I fixed the debugging code and then set out for a long bug
hunting session. It took me about a week full time work - poking around
various places in the driver, reading Don Becker's and Jeff Garzik's Linux
driver and even the FreeBSD driver (what a piece of crap!) - and
eventually spotted the nasty thing: the transmit routine was acknowledging
each and every interrupt pending, including the RxOverrun and RxFIFIOver
interrupts. This confused the RTL8139 thoroughly. It destroyed the
Rx ring contents by dumping the 2K FIFO contents right where we wanted to
get the next packet. Oh well, what fun.
18 Jan 2000 mdc@thinguin.org (Marty Connor)
Drastically simplified error handling. Basically, if any error
in transmission or reception occurs, the card is reset.
Also, pointed all transmit descriptors to the same buffer to
save buffer space. This should decrease driver size and avoid
corruption because of exceeding 32K during runtime.
28 Jul 1999 (Matthias Meixner - meixner@rbg.informatik.tu-darmstadt.de)
rtl_poll was quite broken: it used the RxOK interrupt flag instead
of the RxBufferEmpty flag which often resulted in very bad
transmission performace - below 1kBytes/s.
*/
#include "etherboot.h"
#include "nic.h"
#include "pci.h"
#include "cards.h"
#define RTL_TIMEOUT (1*TICKS_PER_SEC)
/* PCI Tuning Parameters
Threshold is bytes transferred to chip before transmission starts. */
#define TX_FIFO_THRESH 256 /* In bytes, rounded down to 32 byte units. */
#define RX_FIFO_THRESH 4 /* Rx buffer level before first PCI xfer. */
#define RX_DMA_BURST 4 /* Maximum PCI burst, '4' is 256 bytes */
#define TX_DMA_BURST 4 /* Calculate as 16<<val. */
#define NUM_TX_DESC 4 /* Number of Tx descriptor registers. */
#define TX_BUF_SIZE (ETH_MAX_PACKET-4) /* FCS is added by the chip */
#define RX_BUF_LEN_IDX 0 /* 0, 1, 2 is allowed - 8,16,32K rx buffer */
#define RX_BUF_LEN (8192 << RX_BUF_LEN_IDX)
#undef DEBUG_TX
#undef DEBUG_RX
/* Symbolic offsets to registers. */
enum RTL8139_registers {
MAC0=0, /* Ethernet hardware address. */
MAR0=8, /* Multicast filter. */
TxStatus0=0x10, /* Transmit status (four 32bit registers). */
TxAddr0=0x20, /* Tx descriptors (also four 32bit). */
RxBuf=0x30, RxEarlyCnt=0x34, RxEarlyStatus=0x36,
ChipCmd=0x37, RxBufPtr=0x38, RxBufAddr=0x3A,
IntrMask=0x3C, IntrStatus=0x3E,
TxConfig=0x40, RxConfig=0x44,
Timer=0x48, /* general-purpose counter. */
RxMissed=0x4C, /* 24 bits valid, write clears. */
Cfg9346=0x50, Config0=0x51, Config1=0x52,
TimerIntrReg=0x54, /* intr if gp counter reaches this value */
MediaStatus=0x58,
Config3=0x59,
MultiIntr=0x5C,
RevisionID=0x5E, /* revision of the RTL8139 chip */
TxSummary=0x60,
MII_BMCR=0x62, MII_BMSR=0x64, NWayAdvert=0x66, NWayLPAR=0x68,
NWayExpansion=0x6A,
DisconnectCnt=0x6C, FalseCarrierCnt=0x6E,
NWayTestReg=0x70,
RxCnt=0x72, /* packet received counter */
CSCR=0x74, /* chip status and configuration register */
PhyParm1=0x78,TwisterParm=0x7c,PhyParm2=0x80, /* undocumented */
/* from 0x84 onwards are a number of power management/wakeup frame
* definitions we will probably never need to know about. */
};
enum ChipCmdBits {
CmdReset=0x10, CmdRxEnb=0x08, CmdTxEnb=0x04, RxBufEmpty=0x01, };
/* Interrupt register bits, using my own meaningful names. */
enum IntrStatusBits {
PCIErr=0x8000, PCSTimeout=0x4000, CableLenChange= 0x2000,
RxFIFOOver=0x40, RxUnderrun=0x20, RxOverflow=0x10,
TxErr=0x08, TxOK=0x04, RxErr=0x02, RxOK=0x01,
};
enum TxStatusBits {
TxHostOwns=0x2000, TxUnderrun=0x4000, TxStatOK=0x8000,
TxOutOfWindow=0x20000000, TxAborted=0x40000000,
TxCarrierLost=0x80000000,
};
enum RxStatusBits {
RxMulticast=0x8000, RxPhysical=0x4000, RxBroadcast=0x2000,
RxBadSymbol=0x0020, RxRunt=0x0010, RxTooLong=0x0008, RxCRCErr=0x0004,
RxBadAlign=0x0002, RxStatusOK=0x0001,
};
enum MediaStatusBits {
MSRTxFlowEnable=0x80, MSRRxFlowEnable=0x40, MSRSpeed10=0x08,
MSRLinkFail=0x04, MSRRxPauseFlag=0x02, MSRTxPauseFlag=0x01,
};
enum MIIBMCRBits {
BMCRReset=0x8000, BMCRSpeed100=0x2000, BMCRNWayEnable=0x1000,
BMCRRestartNWay=0x0200, BMCRDuplex=0x0100,
};
enum CSCRBits {
CSCR_LinkOKBit=0x0400, CSCR_LinkChangeBit=0x0800,
CSCR_LinkStatusBits=0x0f000, CSCR_LinkDownOffCmd=0x003c0,
CSCR_LinkDownCmd=0x0f3c0,
};
/* Bits in RxConfig. */
enum rx_mode_bits {
RxCfgWrap=0x80,
AcceptErr=0x20, AcceptRunt=0x10, AcceptBroadcast=0x08,
AcceptMulticast=0x04, AcceptMyPhys=0x02, AcceptAllPhys=0x01,
};
static int ioaddr;
static unsigned int cur_rx,cur_tx;
/* The RTL8139 can only transmit from a contiguous, aligned memory block. */
static unsigned char tx_buffer[TX_BUF_SIZE] __attribute__((aligned(4)));
/* I know that this is a MEGA HACK, but the tagged boot image specification
* states that we can do whatever we want below 0x10000 - so we do! */
/* But we still give the user the choice of using an internal buffer
just in case - Ken */
#ifdef USE_INTERNAL_BUFFER
static unsigned char rx_ring[RX_BUF_LEN+16] __attribute__((aligned(4)));
#else
#define rx_ring ((unsigned char *)(0x10000 - (RX_BUF_LEN + 16)))
#endif
struct nic *rtl8139_probe(struct nic *nic, unsigned short *probeaddrs,
struct pci_device *pci);
static int read_eeprom(int location);
static void rtl_reset(struct nic *nic);
static void rtl_transmit(struct nic *nic, const char *destaddr,
unsigned int type, unsigned int len, const char *data);
static int rtl_poll(struct nic *nic);
static void rtl_disable(struct nic*);
struct nic *rtl8139_probe(struct nic *nic, unsigned short *probeaddrs,
struct pci_device *pci)
{
int i;
struct pci_device *p;
int speed10, fullduplex;
/* There are enough "RTL8139" strings on the console already, so
* be brief and concentrate on the interesting pieces of info... */
printf(" - ");
if (probeaddrs == 0 || probeaddrs[0] == 0) {
printf("\nERROR: no probeaddrs given, using pci_device\n");
for (p = pci; p->vendor; p++) {
if ( ( (p->vendor == PCI_VENDOR_ID_REALTEK)
&& (p->dev_id == PCI_DEVICE_ID_REALTEK_8139) )
|| ( (p->vendor == PCI_VENDOR_ID_SMC_1211)
&& (p->dev_id == PCI_DEVICE_ID_SMC_1211) ) ) {
probeaddrs[0] = p->ioaddr;
printf("rtl8139: probing %x (membase %x)\n",
p->ioaddr, p->membase);
}
}
return 0;
}
/* Mask the bit that says "this is an io addr" */
ioaddr = probeaddrs[0] & ~3;
/* Bring the chip out of low-power mode. */
outb(0x00, ioaddr + Config1);
if (read_eeprom(0) != 0xffff) {
unsigned short *ap = (unsigned short*)nic->node_addr;
for (i = 0; i < 3; i++)
*ap++ = read_eeprom(i + 7);
} else {
unsigned char *ap = (unsigned char*)nic->node_addr;
for (i = 0; i < ETHER_ADDR_SIZE; i++)
*ap++ = inb(ioaddr + MAC0 + i);
}
printf("ioaddr 0x%x, addr ", ioaddr);
for (i = 0; i < ETHER_ADDR_SIZE; i++) {
printf("%b", nic->node_addr[i]);
if (i < ETHER_ADDR_SIZE-1) putchar(':');
}
speed10 = inb(ioaddr + MediaStatus) & MSRSpeed10;
fullduplex = inw(ioaddr + MII_BMCR) & BMCRDuplex;
printf(" %sMbps %s-duplex\n", speed10 ? "10" : "100",
fullduplex ? "full" : "half");
rtl_reset(nic);
nic->reset = rtl_reset;
nic->poll = rtl_poll;
nic->transmit = rtl_transmit;
nic->disable = rtl_disable;
return nic;
}
/* Serial EEPROM section. */
/* EEPROM_Ctrl bits. */
#define EE_SHIFT_CLK 0x04 /* EEPROM shift clock. */
#define EE_CS 0x08 /* EEPROM chip select. */
#define EE_DATA_WRITE 0x02 /* EEPROM chip data in. */
#define EE_WRITE_0 0x00
#define EE_WRITE_1 0x02
#define EE_DATA_READ 0x01 /* EEPROM chip data out. */
#define EE_ENB (0x80 | EE_CS)
/*
Delay between EEPROM clock transitions.
No extra delay is needed with 33Mhz PCI, but 66Mhz may change this.
*/
#define eeprom_delay() inl(ee_addr)
/* The EEPROM commands include the alway-set leading bit. */
#define EE_WRITE_CMD (5 << 6)
#define EE_READ_CMD (6 << 6)
#define EE_ERASE_CMD (7 << 6)
static int read_eeprom(int location)
{
int i;
unsigned int retval = 0;
long ee_addr = ioaddr + Cfg9346;
int read_cmd = location | EE_READ_CMD;
outb(EE_ENB & ~EE_CS, ee_addr);
outb(EE_ENB, ee_addr);
/* Shift the read command bits out. */
for (i = 10; i >= 0; i--) {
int dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
outb(EE_ENB | dataval, ee_addr);
eeprom_delay();
outb(EE_ENB | dataval | EE_SHIFT_CLK, ee_addr);
eeprom_delay();
}
outb(EE_ENB, ee_addr);
eeprom_delay();
for (i = 16; i > 0; i--) {
outb(EE_ENB | EE_SHIFT_CLK, ee_addr);
eeprom_delay();
retval = (retval << 1) | ((inb(ee_addr) & EE_DATA_READ) ? 1 : 0);
outb(EE_ENB, ee_addr);
eeprom_delay();
}
/* Terminate the EEPROM access. */
outb(~EE_CS, ee_addr);
return retval;
}
static void rtl_reset(struct nic* nic)
{
int i;
outb(CmdReset, ioaddr + ChipCmd);
cur_rx = 0;
cur_tx = 0;
/* Check that the chip has finished the reset. */
for (i = 1000; i > 0; i--)
if ((inb(ioaddr + ChipCmd) & CmdReset) == 0)
break;
for (i = 0; i < 6; i++)
outb(nic->node_addr[i], ioaddr + MAC0 + i);
/* Must enable Tx/Rx before setting transfer thresholds! */
outb(CmdRxEnb | CmdTxEnb, ioaddr + ChipCmd);
outl((RX_FIFO_THRESH<<13) | (RX_BUF_LEN_IDX<<11) | (RX_DMA_BURST<<8),
ioaddr + RxConfig); /* accept no frames yet! */
outl((TX_DMA_BURST<<8)|0x03000000, ioaddr + TxConfig);
/* The Linux driver changes Config1 here to use a different LED pattern
* for half duplex or full/autodetect duplex (for full/autodetect, the
* outputs are TX/RX, Link10/100, FULL, while for half duplex it uses
* TX/RX, Link100, Link10). This is messy, because it doesn't match
* the inscription on the mounting bracket. It should not be changed
* from the configuration EEPROM default, because the card manufacturer
* should have set that to match the card. */
#ifdef DEBUG_RX
printf("rx ring address is %X\n",(unsigned long)rx_ring);
#endif
outl((unsigned long)rx_ring, ioaddr + RxBuf);
/* Start the chip's Tx and Rx process. */
outl(0, ioaddr + RxMissed);
/* set_rx_mode */
outb(AcceptBroadcast|AcceptMyPhys, ioaddr + RxConfig);
/* If we add multicast support, the MAR0 register would have to be
* initialized to 0xffffffffffffffff (two 32 bit accesses). Etherboot
* only needs broadcast (for ARP/RARP/BOOTP/DHCP) and unicast. */
outb(CmdRxEnb | CmdTxEnb, ioaddr + ChipCmd);
/* Disable all known interrupts by setting the interrupt mask. */
outw(0, ioaddr + IntrMask);
}
static void rtl_transmit(struct nic *nic, const char *destaddr,
unsigned int type, unsigned int len, const char *data)
{
unsigned int status, to, nstype;
unsigned long txstatus;
memcpy(tx_buffer, destaddr, ETHER_ADDR_SIZE);
memcpy(tx_buffer + ETHER_ADDR_SIZE, nic->node_addr, ETHER_ADDR_SIZE);
nstype = htons(type);
memcpy(tx_buffer + 2 * ETHER_ADDR_SIZE, (char*)&nstype, 2);
memcpy(tx_buffer + ETHER_HDR_SIZE, data, len);
len += ETHER_HDR_SIZE;
#ifdef DEBUG_TX
printf("sending %d bytes ethtype %x\n", len, type);
#endif
/* Note: RTL8139 doesn't auto-pad, send minimum payload (another 4
* bytes are sent automatically for the FCS, totalling to 64 bytes). */
while (len < ETH_MIN_PACKET - 4) {
tx_buffer[len++] = '\0';
}
outl((unsigned long)tx_buffer, ioaddr + TxAddr0 + cur_tx*4);
outl(((TX_FIFO_THRESH<<11) & 0x003f0000) | len,
ioaddr + TxStatus0 + cur_tx*4);
to = currticks() + RTL_TIMEOUT;
do {
status = inw(ioaddr + IntrStatus);
/* Only acknlowledge interrupt sources we can properly handle
* here - the RxOverflow/RxFIFOOver MUST be handled in the
* rtl_poll() function. */
outw(status & (TxOK | TxErr | PCIErr), ioaddr + IntrStatus);
if ((status & (TxOK | TxErr | PCIErr)) != 0) break;
} while (currticks() < to);
txstatus = inl(ioaddr+ TxStatus0 + cur_tx*4);
if (status & TxOK) {
cur_tx = ++cur_tx % NUM_TX_DESC;
#ifdef DEBUG_TX
printf("tx done (%d ticks), status %x txstatus %X\n",
to-currticks(), status, txstatus);
#endif
} else {
#ifdef DEBUG_TX
printf("tx timeout/error (%d ticks), status %x txstatus %X\n",
currticks()-to, status, txstatus);
#endif
rtl_reset(nic);
}
}
static int rtl_poll(struct nic *nic)
{
unsigned int status;
unsigned int ring_offs;
unsigned int rx_size, rx_status;
if (inb(ioaddr + ChipCmd) & RxBufEmpty) {
return 0;
}
status = inw(ioaddr + IntrStatus);
/* See below for the rest of the interrupt acknowledges. */
outw(status & ~(RxFIFOOver | RxOverflow | RxOK), ioaddr + IntrStatus);
#ifdef DEBUG_RX
printf("rtl_poll: int %x ", status);
#endif
ring_offs = cur_rx % RX_BUF_LEN;
rx_status = *(unsigned int*)(rx_ring + ring_offs);
rx_size = rx_status >> 16;
rx_status &= 0xffff;
if ((rx_status & (RxBadSymbol|RxRunt|RxTooLong|RxCRCErr|RxBadAlign)) ||
(rx_size < ETH_MIN_PACKET) || (rx_size > ETH_MAX_PACKET)) {
printf("rx error %x\n", rx_status);
rtl_reset(nic); /* this clears all interrupts still pending */
return 0;
}
/* Received a good packet */
nic->packetlen = rx_size - 4; /* no one cares about the FCS */
if (ring_offs+4+rx_size-4 > RX_BUF_LEN) {
int semi_count = RX_BUF_LEN - ring_offs - 4;
memcpy(nic->packet, rx_ring + ring_offs + 4, semi_count);
memcpy(nic->packet+semi_count, rx_ring, rx_size-4-semi_count);
#ifdef DEBUG_RX
printf("rx packet %d+%d bytes", semi_count,rx_size-4-semi_count);
#endif
} else {
memcpy(nic->packet, rx_ring + ring_offs + 4, nic->packetlen);
#ifdef DEBUG_RX
printf("rx packet %d bytes", rx_size-4);
#endif
}
#ifdef DEBUG_RX
printf(" at %X type %b%b rxstatus %x\n",
(unsigned long)(rx_ring+ring_offs+4),
nic->packet[12], nic->packet[13], rx_status);
#endif
cur_rx = (cur_rx + rx_size + 4 + 3) & ~3;
outw(cur_rx - 16, ioaddr + RxBufPtr);
/* See RTL8139 Programming Guide V0.1 for the official handling of
* Rx overflow situations. The document itself contains basically no
* usable information, except for a few exception handling rules. */
outw(status & (RxFIFOOver | RxOverflow | RxOK), ioaddr + IntrStatus);
return 1;
}
static void rtl_disable(struct nic *nic)
{
}