netboot/epic100.h - grub4dos-solaris - Rivoreo Source Code Repositories

 #ifndef _EPIC100_H_
 # define _EPIC100_H_

 #ifndef PCI_VENDOR_SMC
 # define PCI_VENDOR_SMC		0x10B8
 #endif

 #ifndef PCI_DEVICE_SMC_EPIC100
 # define PCI_DEVICE_SMC_EPIC100	0x0005
 #endif

 #define PCI_DEVICE_ID_NONE	0xFFFF

 /* Offsets to registers (using SMC names). */
 enum epic100_registers {
     COMMAND= 0,		/* Control Register */
     INTSTAT= 4,		/* Interrupt Status */
     INTMASK= 8,		/* Interrupt Mask */
     GENCTL = 0x0C, 	/* General Control */
     NVCTL  = 0x10,	/* Non Volatile Control */
     EECTL  = 0x14,	/* EEPROM Control  */
     TEST   = 0x1C, 	/* Test register: marked as reserved (see in source code) */
     CRCCNT = 0x20,	/* CRC Error Counter */
     ALICNT = 0x24, 	/* Frame Alignment Error Counter */
     MPCNT  = 0x28,	/* Missed Packet Counter */
     MMCTL  = 0x30,	/* MII Management Interface Control */
     MMDATA = 0x34, 	/* MII Management Interface Data */
     MIICFG = 0x38,	/* MII Configuration */
     IPG    = 0x3C,	/* InterPacket Gap */
     LAN0   = 0x40,	/* MAC address. (0x40-0x48) */
     IDCHK  = 0x4C,	/* BoardID/ Checksum */
     MC0    = 0x50,	/* Multicast filter table. (0x50-0x5c) */
     RXCON  = 0x60, 	/* Receive Control */
     TXCON  = 0x70, 	/* Transmit Control */
     TXSTAT = 0x74,	/* Transmit Status */
     PRCDAR = 0x84, 	/* PCI Receive Current Descriptor Address */
     PRSTAT = 0xA4,	/* PCI Receive DMA Status */
     PRCPTHR= 0xB0,	/* PCI Receive Copy Threshold */
     PTCDAR = 0xC4,	/* PCI Transmit Current Descriptor Address */
     ETHTHR = 0xDC	/* Early Transmit Threshold */
 };

 /* Command register (CR_) bits */
 #define CR_STOP_RX		(0x00000001)
 #define CR_START_RX		(0x00000002)
 #define CR_QUEUE_TX		(0x00000004)
 #define CR_QUEUE_RX		(0x00000008)
 #define CR_NEXTFRAME		(0x00000010)
 #define CR_STOP_TX_DMA		(0x00000020)
 #define CR_STOP_RX_DMA		(0x00000040)
 #define CR_TX_UGO		(0x00000080)

 /* Interrupt register bits. NI means No Interrupt generated */

 #define	INTR_RX_THR_STA		(0x00400000) 	/* rx copy threshold status NI */
 #define	INTR_RX_BUFF_EMPTY	(0x00200000)	/* rx buffers empty. NI */
 #define	INTR_TX_IN_PROG		(0x00100000)	/* tx copy in progess. NI */
 #define	INTR_RX_IN_PROG		(0x00080000)	/* rx copy in progress. NI */
 #define	INTR_TXIDLE		(0x00040000)	/* tx idle. NI */
 #define INTR_RXIDLE		(0x00020000)	/* rx idle. NI */
 #define INTR_INTR_ACTIVE	(0x00010000)	/* Interrupt active. NI */
 #define INTR_RX_STATUS_OK	(0x00008000)	/* rx status valid. NI */
 #define INTR_PCI_TGT_ABT	(0x00004000)	/* PCI Target abort */
 #define INTR_PCI_MASTER_ABT	(0x00002000)	/* PCI Master abort */
 #define INTR_PCI_PARITY_ERR	(0x00001000)	/* PCI adress parity error */
 #define INTR_PCI_DATA_ERR	(0x00000800)	/* PCI data parity error */
 #define INTR_RX_THR_CROSSED	(0x00000400)	/* rx copy threshold crossed */
 #define INTR_CNTFULL		(0x00000200)	/* Counter overflow */
 #define INTR_TXUNDERRUN		(0x00000100)	/* tx underrun. */
 #define INTR_TXEMPTY		(0x00000080)	/* tx queue empty */
 #define INTR_TX_CH_COMPLETE	(0x00000040)	/* tx chain complete */
 #define INTR_TXDONE		(0x00000020)	/* tx complete (w or w/o err) */
 #define INTR_RXERROR		(0x00000010)	/* rx error (CRC) */
 #define INTR_RXOVERFLOW		(0x00000008)	/* rx buffer overflow */
 #define INTR_RX_QUEUE_EMPTY	(0x00000004)	/* rx queue empty. */
 #define INTR_RXHEADER		(0x00000002)	/* header copy complete */
 #define INTR_RXDONE		(0x00000001)	/* Receive copy complete */

 #define INTR_CLEARINTR		(0x00007FFF)
 #define INTR_VALIDBITS		(0x007FFFFF)
 #define INTR_DISABLE		(0x00000000)
 #define INTR_CLEARERRS		(0x00007F18)
 #define INTR_ABNINTR		(INTR_CNTFULL | INTR_TXUNDERRUN | INTR_RXOVERFLOW)

 /* General Control (GC_) bits */

 #define GC_SOFT_RESET		(0x00000001)
 #define GC_INTR_ENABLE		(0x00000002)
 #define GC_SOFT_INTR		(0x00000004)
 #define GC_POWER_DOWN		(0x00000008)
 #define GC_ONE_COPY		(0x00000010)
 #define GC_BIG_ENDIAN		(0x00000020)
 #define GC_RX_PREEMPT_TX	(0x00000040)
 #define GC_TX_PREEMPT_RX	(0x00000080)

 /*
  * Receive FIFO Threshold values
  * Control the level at which the  PCI burst state machine
  * begins to empty the receive FIFO. Possible values: 0-3
  *
  * 0 => 32, 1 => 64, 2 => 96 3 => 128 bytes.
  */
 #define GC_RX_FIFO_THR_32	(0x00000000)
 #define GC_RX_FIFO_THR_64	(0x00000100)
 #define GC_RX_FIFO_THR_96	(0x00000200)
 #define GC_RX_FIFO_THR_128	(0x00000300)

 /* Memory Read Control (MRC_) values */
 #define GC_MRC_MEM_READ		(0x00000000)
 #define GC_MRC_READ_MULT	(0x00000400)
 #define GC_MRC_READ_LINE	(0x00000800)

 #define GC_SOFTBIT0		(0x00001000)
 #define GC_SOFTBIT1		(0x00002000)
 #define GC_RESET_PHY		(0x00004000)

 /* Definitions of the Receive Control (RC_) register bits */

 #define RC_SAVE_ERRORED_PKT	(0x00000001)
 #define RC_SAVE_RUNT_FRAMES	(0x00000002)
 #define RC_RCV_BROADCAST	(0x00000004)
 #define RC_RCV_MULTICAST	(0x00000008)
 #define RC_RCV_INVERSE_PKT	(0x00000010)
 #define RC_PROMISCUOUS_MODE	(0x00000020)
 #define RC_MONITOR_MODE		(0x00000040)
 #define RC_EARLY_RCV_ENABLE	(0x00000080)

 /* description of the rx descriptors control bits */
 #define RD_FRAGLIST		(0x0001)	/* Desc points to a fragment list */
 #define RD_LLFORM		(0x0002)	/* Frag list format */
 #define RD_HDR_CPY		(0x0004)	/* Desc used for header copy */

 /* Definition of the Transmit CONTROL (TC) register bits */

 #define TC_EARLY_TX_ENABLE	(0x00000001)

 /* Loopback Mode (LM_) Select valuesbits */
 #define TC_LM_NORMAL		(0x00000000)
 #define TC_LM_INTERNAL		(0x00000002)
 #define TC_LM_EXTERNAL		(0x00000004)
 #define TC_LM_FULL_DPX		(0x00000006)

 #define TX_SLOT_TIME		(0x00000078)

 /* Bytes transferred to chip before transmission starts. */
 #define TX_FIFO_THRESH 		128	/* Rounded down to 4 byte units. */

 /* description of rx descriptors status bits */
 #define RRING_PKT_INTACT	(0x0001)
 #define RRING_ALIGN_ERR		(0x0002)
 #define RRING_CRC_ERR		(0x0004)
 #define RRING_MISSED_PKT	(0x0008)
 #define RRING_MULTICAST		(0x0010)
 #define RRING_BROADCAST		(0x0020)
 #define RRING_RECEIVER_DISABLE	(0x0040)
 #define RRING_STATUS_VALID	(0x1000)
 #define RRING_FRAGLIST_ERR	(0x2000)
 #define RRING_HDR_COPIED	(0x4000)
 #define RRING_OWN		(0x8000)

 /* error summary */
 #define RRING_ERROR		(RRING_ALIGN_ERR|RRING_CRC_ERR)

 /* description of tx descriptors status bits */
 #define TRING_PKT_INTACT	(0x0001)	/* pkt transmitted. */
 #define TRING_PKT_NONDEFER	(0x0002)	/* pkt xmitted w/o deferring */
 #define TRING_COLL		(0x0004)	/* pkt xmitted w collisions */
 #define TRING_CARR		(0x0008)	/* carrier sense lost */
 #define TRING_UNDERRUN		(0x0010)	/* DMA underrun */
 #define TRING_HB_COLL		(0x0020)	/* Collision detect Heartbeat */
 #define TRING_WIN_COLL		(0x0040)	/* out of window collision */
 #define TRING_DEFERRED		(0x0080)	/* Deferring */
 #define TRING_COLL_COUNT	(0x0F00)	/* collision counter (mask) */
 #define TRING_COLL_EXCESS	(0x1000)	/* tx aborted: excessive colls */
 #define TRING_OWN		(0x8000)	/* desc ownership bit */

 /* error summary */
 #define TRING_ABORT	(TRING_COLL_EXCESS|TRING_WIN_COLL|TRING_UNDERRUN)
 #define TRING_ERROR	(TRING_DEFERRED|TRING_WIN_COLL|TRING_UNDERRUN|TRING_CARR/*|TRING_COLL*/ )

 /* description of the tx descriptors control bits */
 #define TD_FRAGLIST		(0x0001)	/* Desc points to a fragment list */
 #define TD_LLFORM		(0x0002)	/* Frag list format */
 #define TD_IAF			(0x0004)	/* Generate Interrupt after tx */
 #define TD_NOCRC		(0x0008)	/* No CRC generated */
 #define TD_LASTDESC		(0x0010)	/* Last desc for this frame */

 #endif /* _EPIC100_H_ */
	#ifndef _EPIC100_H_
	# define _EPIC100_H_

	#ifndef PCI_VENDOR_SMC
	# define PCI_VENDOR_SMC 0x10B8
	#endif

	#ifndef PCI_DEVICE_SMC_EPIC100
	# define PCI_DEVICE_SMC_EPIC100 0x0005
	#endif

	#define PCI_DEVICE_ID_NONE 0xFFFF

	/* Offsets to registers (using SMC names). */
	enum epic100_registers {
	COMMAND= 0, /* Control Register */
	INTSTAT= 4, /* Interrupt Status */
	INTMASK= 8, /* Interrupt Mask */
	GENCTL = 0x0C, /* General Control */
	NVCTL = 0x10, /* Non Volatile Control */
	EECTL = 0x14, /* EEPROM Control */
	TEST = 0x1C, /* Test register: marked as reserved (see in source code) */
	CRCCNT = 0x20, /* CRC Error Counter */
	ALICNT = 0x24, /* Frame Alignment Error Counter */
	MPCNT = 0x28, /* Missed Packet Counter */
	MMCTL = 0x30, /* MII Management Interface Control */
	MMDATA = 0x34, /* MII Management Interface Data */
	MIICFG = 0x38, /* MII Configuration */
	IPG = 0x3C, /* InterPacket Gap */
	LAN0 = 0x40, /* MAC address. (0x40-0x48) */
	IDCHK = 0x4C, /* BoardID/ Checksum */
	MC0 = 0x50, /* Multicast filter table. (0x50-0x5c) */
	RXCON = 0x60, /* Receive Control */
	TXCON = 0x70, /* Transmit Control */
	TXSTAT = 0x74, /* Transmit Status */
	PRCDAR = 0x84, /* PCI Receive Current Descriptor Address */
	PRSTAT = 0xA4, /* PCI Receive DMA Status */
	PRCPTHR= 0xB0, /* PCI Receive Copy Threshold */
	PTCDAR = 0xC4, /* PCI Transmit Current Descriptor Address */
	ETHTHR = 0xDC /* Early Transmit Threshold */
	};

	/* Command register (CR_) bits */
	#define CR_STOP_RX (0x00000001)
	#define CR_START_RX (0x00000002)
	#define CR_QUEUE_TX (0x00000004)
	#define CR_QUEUE_RX (0x00000008)
	#define CR_NEXTFRAME (0x00000010)
	#define CR_STOP_TX_DMA (0x00000020)
	#define CR_STOP_RX_DMA (0x00000040)
	#define CR_TX_UGO (0x00000080)

	/* Interrupt register bits. NI means No Interrupt generated */

	#define INTR_RX_THR_STA (0x00400000) /* rx copy threshold status NI */
	#define INTR_RX_BUFF_EMPTY (0x00200000) /* rx buffers empty. NI */
	#define INTR_TX_IN_PROG (0x00100000) /* tx copy in progess. NI */
	#define INTR_RX_IN_PROG (0x00080000) /* rx copy in progress. NI */
	#define INTR_TXIDLE (0x00040000) /* tx idle. NI */
	#define INTR_RXIDLE (0x00020000) /* rx idle. NI */
	#define INTR_INTR_ACTIVE (0x00010000) /* Interrupt active. NI */
	#define INTR_RX_STATUS_OK (0x00008000) /* rx status valid. NI */
	#define INTR_PCI_TGT_ABT (0x00004000) /* PCI Target abort */
	#define INTR_PCI_MASTER_ABT (0x00002000) /* PCI Master abort */
	#define INTR_PCI_PARITY_ERR (0x00001000) /* PCI adress parity error */
	#define INTR_PCI_DATA_ERR (0x00000800) /* PCI data parity error */
	#define INTR_RX_THR_CROSSED (0x00000400) /* rx copy threshold crossed */
	#define INTR_CNTFULL (0x00000200) /* Counter overflow */
	#define INTR_TXUNDERRUN (0x00000100) /* tx underrun. */
	#define INTR_TXEMPTY (0x00000080) /* tx queue empty */
	#define INTR_TX_CH_COMPLETE (0x00000040) /* tx chain complete */
	#define INTR_TXDONE (0x00000020) /* tx complete (w or w/o err) */
	#define INTR_RXERROR (0x00000010) /* rx error (CRC) */
	#define INTR_RXOVERFLOW (0x00000008) /* rx buffer overflow */
	#define INTR_RX_QUEUE_EMPTY (0x00000004) /* rx queue empty. */
	#define INTR_RXHEADER (0x00000002) /* header copy complete */
	#define INTR_RXDONE (0x00000001) /* Receive copy complete */

	#define INTR_CLEARINTR (0x00007FFF)
	#define INTR_VALIDBITS (0x007FFFFF)
	#define INTR_DISABLE (0x00000000)
	#define INTR_CLEARERRS (0x00007F18)
	#define INTR_ABNINTR (INTR_CNTFULL \| INTR_TXUNDERRUN \| INTR_RXOVERFLOW)

	/* General Control (GC_) bits */

	#define GC_SOFT_RESET (0x00000001)
	#define GC_INTR_ENABLE (0x00000002)
	#define GC_SOFT_INTR (0x00000004)
	#define GC_POWER_DOWN (0x00000008)
	#define GC_ONE_COPY (0x00000010)
	#define GC_BIG_ENDIAN (0x00000020)
	#define GC_RX_PREEMPT_TX (0x00000040)
	#define GC_TX_PREEMPT_RX (0x00000080)

	/*
	* Receive FIFO Threshold values
	* Control the level at which the PCI burst state machine
	* begins to empty the receive FIFO. Possible values: 0-3
	*
	* 0 => 32, 1 => 64, 2 => 96 3 => 128 bytes.
	*/
	#define GC_RX_FIFO_THR_32 (0x00000000)
	#define GC_RX_FIFO_THR_64 (0x00000100)
	#define GC_RX_FIFO_THR_96 (0x00000200)
	#define GC_RX_FIFO_THR_128 (0x00000300)

	/* Memory Read Control (MRC_) values */
	#define GC_MRC_MEM_READ (0x00000000)
	#define GC_MRC_READ_MULT (0x00000400)
	#define GC_MRC_READ_LINE (0x00000800)

	#define GC_SOFTBIT0 (0x00001000)
	#define GC_SOFTBIT1 (0x00002000)
	#define GC_RESET_PHY (0x00004000)

	/* Definitions of the Receive Control (RC_) register bits */

	#define RC_SAVE_ERRORED_PKT (0x00000001)
	#define RC_SAVE_RUNT_FRAMES (0x00000002)
	#define RC_RCV_BROADCAST (0x00000004)
	#define RC_RCV_MULTICAST (0x00000008)
	#define RC_RCV_INVERSE_PKT (0x00000010)
	#define RC_PROMISCUOUS_MODE (0x00000020)
	#define RC_MONITOR_MODE (0x00000040)
	#define RC_EARLY_RCV_ENABLE (0x00000080)

	/* description of the rx descriptors control bits */
	#define RD_FRAGLIST (0x0001) /* Desc points to a fragment list */
	#define RD_LLFORM (0x0002) /* Frag list format */
	#define RD_HDR_CPY (0x0004) /* Desc used for header copy */

	/* Definition of the Transmit CONTROL (TC) register bits */

	#define TC_EARLY_TX_ENABLE (0x00000001)

	/* Loopback Mode (LM_) Select valuesbits */
	#define TC_LM_NORMAL (0x00000000)
	#define TC_LM_INTERNAL (0x00000002)
	#define TC_LM_EXTERNAL (0x00000004)
	#define TC_LM_FULL_DPX (0x00000006)

	#define TX_SLOT_TIME (0x00000078)

	/* Bytes transferred to chip before transmission starts. */
	#define TX_FIFO_THRESH 128 /* Rounded down to 4 byte units. */

	/* description of rx descriptors status bits */
	#define RRING_PKT_INTACT (0x0001)
	#define RRING_ALIGN_ERR (0x0002)
	#define RRING_CRC_ERR (0x0004)
	#define RRING_MISSED_PKT (0x0008)
	#define RRING_MULTICAST (0x0010)
	#define RRING_BROADCAST (0x0020)
	#define RRING_RECEIVER_DISABLE (0x0040)
	#define RRING_STATUS_VALID (0x1000)
	#define RRING_FRAGLIST_ERR (0x2000)
	#define RRING_HDR_COPIED (0x4000)
	#define RRING_OWN (0x8000)

	/* error summary */
	#define RRING_ERROR (RRING_ALIGN_ERR\|RRING_CRC_ERR)

	/* description of tx descriptors status bits */
	#define TRING_PKT_INTACT (0x0001) /* pkt transmitted. */
	#define TRING_PKT_NONDEFER (0x0002) /* pkt xmitted w/o deferring */
	#define TRING_COLL (0x0004) /* pkt xmitted w collisions */
	#define TRING_CARR (0x0008) /* carrier sense lost */
	#define TRING_UNDERRUN (0x0010) /* DMA underrun */
	#define TRING_HB_COLL (0x0020) /* Collision detect Heartbeat */
	#define TRING_WIN_COLL (0x0040) /* out of window collision */
	#define TRING_DEFERRED (0x0080) /* Deferring */
	#define TRING_COLL_COUNT (0x0F00) /* collision counter (mask) */
	#define TRING_COLL_EXCESS (0x1000) /* tx aborted: excessive colls */
	#define TRING_OWN (0x8000) /* desc ownership bit */

	/* error summary */
	#define TRING_ABORT (TRING_COLL_EXCESS\|TRING_WIN_COLL\|TRING_UNDERRUN)
	#define TRING_ERROR (TRING_DEFERRED\|TRING_WIN_COLL\|TRING_UNDERRUN\|TRING_CARR/\|TRING_COLL/ )

	/* description of the tx descriptors control bits */
	#define TD_FRAGLIST (0x0001) /* Desc points to a fragment list */
	#define TD_LLFORM (0x0002) /* Frag list format */
	#define TD_IAF (0x0004) /* Generate Interrupt after tx */
	#define TD_NOCRC (0x0008) /* No CRC generated */
	#define TD_LASTDESC (0x0010) /* Last desc for this frame */

	#endif /* _EPIC100_H_ */