| /* |
| * linux/mii.h: definitions for MII-compatible transceivers |
| * Originally drivers/net/sunhme.h. |
| * |
| * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com) |
| * |
| * Copied Form Linux 2.4.25 an unneeded items removed by: |
| * Timothy Legge (timlegge at etherboot dot org) |
| * |
| * 03/26/2004 |
| */ |
| |
| /* Generic MII registers. */ |
| |
| #define MII_BMCR 0x00 /* Basic mode control register */ |
| #define MII_BMSR 0x01 /* Basic mode status register */ |
| #define MII_PHYSID1 0x02 /* PHYS ID 1 */ |
| #define MII_PHYSID2 0x03 /* PHYS ID 2 */ |
| #define MII_ADVERTISE 0x04 /* Advertisement control reg */ |
| #define MII_LPA 0x05 /* Link partner ability reg */ |
| #define MII_EXPANSION 0x06 /* Expansion register */ |
| #define MII_DCOUNTER 0x12 /* Disconnect counter */ |
| #define MII_FCSCOUNTER 0x13 /* False carrier counter */ |
| #define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ |
| #define MII_RERRCOUNTER 0x15 /* Receive error counter */ |
| #define MII_SREVISION 0x16 /* Silicon revision */ |
| #define MII_RESV1 0x17 /* Reserved... */ |
| #define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */ |
| #define MII_PHYADDR 0x19 /* PHY address */ |
| #define MII_RESV2 0x1a /* Reserved... */ |
| #define MII_TPISTATUS 0x1b /* TPI status for 10mbps */ |
| #define MII_NCONFIG 0x1c /* Network interface config */ |
| |
| /* Basic mode control register. */ |
| #define BMCR_RESV 0x007f /* Unused... */ |
| #define BMCR_CTST 0x0080 /* Collision test */ |
| #define BMCR_FULLDPLX 0x0100 /* Full duplex */ |
| #define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */ |
| #define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */ |
| #define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */ |
| #define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ |
| #define BMCR_SPEED100 0x2000 /* Select 100Mbps */ |
| #define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */ |
| #define BMCR_RESET 0x8000 /* Reset the DP83840 */ |
| |
| /* Basic mode status register. */ |
| #define BMSR_ERCAP 0x0001 /* Ext-reg capability */ |
| #define BMSR_JCD 0x0002 /* Jabber detected */ |
| #define BMSR_LSTATUS 0x0004 /* Link status */ |
| #define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ |
| #define BMSR_RFAULT 0x0010 /* Remote fault detected */ |
| #define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ |
| #define BMSR_RESV 0x07c0 /* Unused... */ |
| #define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ |
| #define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ |
| #define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ |
| #define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */ |
| #define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */ |
| |
| /* Advertisement control register. */ |
| #define ADVERTISE_SLCT 0x001f /* Selector bits */ |
| #define ADVERTISE_CSMA 0x0001 /* Only selector supported */ |
| #define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */ |
| #define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */ |
| #define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */ |
| #define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */ |
| #define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */ |
| #define ADVERTISE_RESV 0x1c00 /* Unused... */ |
| #define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */ |
| #define ADVERTISE_LPACK 0x4000 /* Ack link partners response */ |
| #define ADVERTISE_NPAGE 0x8000 /* Next page bit */ |
| |
| #define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \ |
| ADVERTISE_CSMA) |
| #define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \ |
| ADVERTISE_100HALF | ADVERTISE_100FULL) |
| |
| /* Link partner ability register. */ |
| #define LPA_SLCT 0x001f /* Same as advertise selector */ |
| #define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */ |
| #define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */ |
| #define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */ |
| #define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */ |
| #define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */ |
| #define LPA_RESV 0x1c00 /* Unused... */ |
| #define LPA_RFAULT 0x2000 /* Link partner faulted */ |
| #define LPA_LPACK 0x4000 /* Link partner acked us */ |
| #define LPA_NPAGE 0x8000 /* Next page bit */ |
| |
| #define LPA_DUPLEX (LPA_10FULL | LPA_100FULL) |
| #define LPA_100 (LPA_100FULL | LPA_100HALF | LPA_100BASE4) |
| |
| /* Expansion register for auto-negotiation. */ |
| #define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */ |
| #define EXPANSION_LCWP 0x0002 /* Got new RX page code word */ |
| #define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */ |
| #define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */ |
| #define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */ |
| #define EXPANSION_RESV 0xffe0 /* Unused... */ |
| |
| /* N-way test register. */ |
| #define NWAYTEST_RESV1 0x00ff /* Unused... */ |
| #define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */ |
| #define NWAYTEST_RESV2 0xfe00 /* Unused... */ |
| |