| SIMH/HP 3000 DIAGNOSTICS PERFORMANCE | |
| ==================================== | |
| Last update: 2016-09-07 | |
| The HP 32230 diagnostic suite has been run against the SIMH HP 3000 simulation. | |
| Diagnostic programs were obtained from two magnetic tapes: HP 30000-11016 Rev. | |
| 1244 (CPU) and 30000-11017 Rev. 2640 (non-CPU). For each diagnostic, the | |
| recommended standard tests were selected, plus any available optional tests that | |
| broadened the test coverage. | |
| Except where noted in the individual diagnostic reports, the test system | |
| configuration is the default SIMH configuration with these changes: | |
| * All I/O devices are enabled. | |
| * The CPU is configured as a Series III with 512KW of memory. | |
| Detailed diagnostic configuration, operation, and results are given after the | |
| summary table. These may be used to duplicate the diagnostic results. | |
| The results of the diagnostic runs are summarized below: | |
| Diag. | |
| File Diagnostic Name Vers. Result | |
| -------- --------------------------------------- ----- ------------- | |
| PD420A CPU Diagnostic Section 1 01.00 Passed | |
| PD420A1 CPU Diagnostic Section 2 01.00 Passed | |
| PD420A2 CPU Diagnostic Section 3 01.01 Passed | |
| PD420A3 CPU Diagnostic Section 4 01.24 Passed | |
| PD420A4 CPU Diagnostic Section 5 01.00 Passed | |
| PD420A5 CPU Diagnostic Section 6 01.00 Passed | |
| PD420A6 CPU Diagnostic Section 7 01.00 Passed | |
| PD420A7 CPU Diagnostic Section 8 01.00 Passed | |
| PD420A8 CPU Diagnostic Section 9 01.00 Passed | |
| PD420A9 CPU Diagnostic Section 10 01.00 Passed | |
| PD420A10 CPU Diagnostic Section 11 01.00 Passed | |
| PD420A11 CPU Diagnostic Section 12 01.00 Passed | |
| PD420A12 CPU Diagnostic Section 13 01.00 Passed | |
| PD420A13 CPU Diagnostic Section 14 01.00 Passed | |
| PD419A 7905A Disc Cartridge 01.04 Partial | |
| PD421A Memory Pattern 01.00 Passed | |
| PD422A Multiplexer Channel 01.02 Passed | |
| PD423A 2888A Disc File 01.00 No simulation | |
| PD424A 7900A Cartridge Disc 01.00 No simulation | |
| PD425A System Clock/Console 01.00 No simulation | |
| PD426A System Clock/Fault Logging Interface 00.00 Passed | |
| PD427A Terminal Data Interface 01.01 Passed | |
| PD428A 2660A Fixed Head Disc 01.00 No simulation | |
| PD429A Selector Channel 01.01 Passed | |
| PD429A Selector Channel Maintenance Board 01.01 Passed | |
| PD430A Error Correction Memory Series II 01.01 No simulation | |
| PD430B Error Correction Memory Series III 00.00 No simulation | |
| PD431A Extended Instruction Set 01.00 No simulation | |
| PD432A Hardwired Serial Interface 01.00 No simulation | |
| PD433A 7970B/E Nine-Track Magnetic Tape 01.04 Partial | |
| PD434A Synchronous Line Controller 01.03 No simulation | |
| PD434B Asynchronous Line Controller 01.04 No simulation | |
| PD435A Universal Interface 01.01 Passed | |
| PD438A Terminal Control Interface 01.00 Passed | |
| PD439A CALCOMP Plotter Interface 01.01 No simulation | |
| PD441A COBOL-II A Firmware 00.00 No simulation | |
| PD442A COBOL-II B Firmware 00.00 No simulation | |
| PD466A Online Line Printer Verifier 01.06 Passed | |
| The "Result" column indicates the level of success in passing the given | |
| diagnostic: | |
| Term Meaning | |
| ------------- --------------------------------------------------------------- | |
| Passed All of the standard tests relevant to the hardware device | |
| passed without error. Optional "utility" tests, where present, | |
| were not run unless they broadened the test coverage. | |
| Partial One or more of the standard tests relevant to the hardware | |
| device were either excluded or failed as expected, due to known | |
| limitations in the simulation, e.g., the lack of "defective | |
| cylinder" flags in a disc simulation. | |
| No simulation A simulation of the hardware device does not exist. | |
| See the "Test Notes" associated with each diagnostic report below for details on | |
| subsets, limitations, or errors encountered. | |
| ===================================================== | |
| 32230 DIAGNOSTIC SUITE DETAILED EXECUTION AND RESULTS | |
| ===================================================== | |
| Each configuration below presumes that the target diagnostic has been cold | |
| loaded from the appropriate magnetic tape. | |
| --------------------- | |
| D420A - CPU Section 1 | |
| --------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> deposit 2000 000001 | |
| sim> deposit 2001 170000 | |
| sim> set cpu stop=pause | |
| sim> go | |
| TEST REPORT: CPU paused, P: 010000 (PAUS 0) | |
| sim> go -b | |
| Programmed halt, CIR: 030366 (HALT 6), P: 010415 (LDI 2) | |
| sim> assert CNTR=0 | |
| sim> go | |
| Programmed halt, CIR: 030367 (HALT 7), P: 010422 (SETR) | |
| sim> assert CNTR=2 | |
| sim> go | |
| Programmed halt, CIR: 030370 (HALT 10), P: 010424 (LOAD DB+1) | |
| sim> assert CNTR=4 | |
| sim> go | |
| Programmed halt, CIR: 030371 (HALT 11), P: 010017 (LOAD DB+1) | |
| sim> assert PB=010004 | |
| sim> assert P=010017 | |
| sim> assert PL=010023 | |
| sim> go | |
| Programmed halt, CIR: 030363 (HALT 3), P: 026170 (RSW) | |
| sim> deposit SWCH 125252 | |
| sim> go | |
| Programmed halt, CIR: 030364 (HALT 4), P: 026201 (RSW) | |
| sim> deposit SWCH 052525 | |
| sim> go | |
| Programmed halt, CIR: 030365 (HALT 5), P: 026212 (RSW) | |
| sim> deposit SWCH 000001 | |
| sim> go | |
| Programmed halt, CIR: 030375 (HALT 15), P: 016250 (ZERO,NOP) | |
| TEST RESULT: Passed. | |
| TEST NOTES: The Internal Switch Register (2000) and Section Select Register | |
| (2001) settings are preconfigured because the SR test seems to | |
| be scheduled before the SSR can be set externally. | |
| ---------------------- | |
| D420A1 - CPU Section 2 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> deposit 2000 000001 | |
| sim> deposit 2001 010000 | |
| sim> go | |
| TEST REPORT: Programmed halt, CIR: 030375 (HALT 15), P: 010141 (LOAD DB+0) | |
| TEST RESULT: Passed. | |
| TEST NOTES: The Internal Switch Register (2000) and Section Select Register | |
| (2001) settings are preconfigured to simplify execution. | |
| ---------------------- | |
| D420A2 - CPU Section 3 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> deposit 2000 000001 | |
| sim> deposit 2001 030000 | |
| sim> go | |
| TEST REPORT: Programmed halt, CIR: 030375 (HALT 15), P: 010163 (ZERO,NOP) | |
| TEST RESULT: Passed. | |
| TEST NOTES: The Internal Switch Register (2000) and Section Select Register | |
| (2001) settings are preconfigured to simplify execution. | |
| Diagnostic tape 30000-11016 Rev. 1244 has a bug in step 2 (SMSK | |
| and RMSK tests). There is a missing INCM DB+5 at the end of the | |
| step. Consequently, the step number in DB+5 is incorrect from | |
| there on, i.e., "step 2" consists of steps 2 and 3, "step 3" is | |
| really step 4, etc., through the end of the diagnostic. There | |
| is no place in the code to insert the missing instruction. | |
| The bug does not affect diagnostic execution. | |
| ---------------------- | |
| D420A3 - CPU Section 4 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> deposit 2000 000001 | |
| sim> deposit 2001 034170 | |
| sim> deposit 015761 051007 | |
| sim> set scmb enable | |
| sim> set scmb mx | |
| sim> set cpu stop=PAUSE | |
| sim> go | |
| TEST REPORT: CPU paused, P: 021376 (PAUS 12) | |
| sim> set cpu nostop=PAUSE | |
| sim> power fail | |
| Programmed halt, CIR: 030374 (HALT 14), P: 011130 (EXIT 0) | |
| sim> power restore | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010630 (ZERO,NOP) | |
| TEST RESULT: Passed. | |
| TEST NOTES: The Internal Switch Register (2000) and Section Select Register | |
| (2001) settings are preconfigured to simplify execution. | |
| The "Stand-Alone HP 30003A/B CPU Diagnostic" manual | |
| (30003-90001, April 1979) says that step 31 has been "eliminated | |
| from diagnostic" (the February 1976 manual lists this step as | |
| "Special Bank Test using special E.T."). However, the | |
| subsequent steps in the manual were not renumbered, although the | |
| code for step 31 and its associated step number increment were | |
| removed. Therefore, all step numbers from hereon are one higher | |
| in the manual than in the diagnostic. | |
| Diagnostic tape 30000-11016 Rev. 1244 has a bug in step 36 (MABS | |
| test). The unpatched diagnostic always skips step 36, as it | |
| thinks that there is only a single memory bank present. | |
| The problem is that the maximum bank number is extracted from | |
| the SSR and written to DB+6 in the test prelude. In previous | |
| tests, there is a LOAD DB+6 and a STOR DB+7 to copy the bank | |
| number to a working variable, and then that variable is used in | |
| a loop to set the bank number to use for the test. In test 36, | |
| however, there is no LOAD/STOR, so the previous value of DB+7 is | |
| used. However, that value is zero, because it was the terminal | |
| count-down value from an earlier test, so the test thinks that | |
| there is only a single bank present. | |
| The fix is to change STOR DB+6 to STOR DB+7 at location 015761. | |
| ---------------------- | |
| D420A4 - CPU Section 5 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> deposit 2000 000001 | |
| sim> deposit 2001 010000 | |
| sim> go | |
| TEST REPORT: Programmed halt, CIR: 030375 (HALT 15), P: 010607 (ZERO,NOP) | |
| TEST RESULT: Passed. | |
| TEST NOTES: The Internal Switch Register (2000) and Section Select Register | |
| (2001) settings are preconfigured to simplify execution. | |
| ---------------------- | |
| D420A5 - CPU Section 6 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 3, P: 010011 (SETR STATUS) | |
| TEST RESULT: Passed. | |
| ---------------------- | |
| D420A6 - CPU Section 7 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 33, P: 010011 (SETR STATUS) | |
| TEST RESULT: Passed. | |
| ---------------------- | |
| D420A7 - CPU Section 8 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 13, P: 010014 (PCAL 0) | |
| TEST RESULT: Passed. | |
| ---------------------- | |
| D420A8 - CPU Section 9 | |
| ---------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 2, P: 010016 (PCAL 0) | |
| TEST RESULT: Passed. | |
| ----------------------- | |
| D420A9 - CPU Section 10 | |
| ----------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 6, P: 010052 (IXIT) | |
| TEST RESULT: Passed. | |
| ------------------------ | |
| D420A10 - CPU Section 11 | |
| ------------------------ | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 9, P: 010011 (PSEB) | |
| TEST RESULT: Passed. | |
| ------------------------ | |
| D420A11 - CPU Section 12 | |
| ------------------------ | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 1, P: 010005 (SETR STATUS) | |
| TEST RESULT: Passed. | |
| ------------------------ | |
| D420A12 - CPU Section 13 | |
| ------------------------ | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 4, P: 010010 (ADDS 0) | |
| TEST RESULT: Passed. | |
| ----------------------------------- | |
| D420A13 - CPU Diagnostic Section 14 | |
| ----------------------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| TEST REPORT: System halt 4, P: 010003 (LDI 0) | |
| TEST RESULT: Passed. | |
| ----------------------------------------- | |
| D419A - Cartridge Disc (user interaction) | |
| ----------------------------------------- | |
| TESTED DEVICE: DS (hp3000_ds.c) | |
| CONFIGURATION: sim> set DS diag=1;0;0;010;D;021 | |
| sim> set DS diag=1;0;0;005;D;021 | |
| sim> set DS diag=1;0;0;010;S;000 | |
| sim> set DS diag=1;0;0;005;S;000 | |
| sim> set DS diag=1;0;0;010;P;000 | |
| sim> set DS diag=1;0;0;005;P;000 | |
| sim> set DS diag=398;1;47;011;;000 | |
| sim> set DS diag=398;1;47;005;;017 | |
| sim> set DS diag=398;1;47;015;;017;0;0;0;0 | |
| sim> set DS diag=398;1;30;011;;000 | |
| sim> set DS diag=398;1;30;005;;017 | |
| sim> set DS diag=398;1;30;015;;017;0;0;0;0 | |
| sim> set DS diag=398;1;25;011;;000 | |
| sim> set DS diag=398;1;25;005;;017 | |
| sim> set DS diag=398;1;25;015;;010;0;0;0;0 | |
| sim> set DS diag=4;1;32;005;;017 | |
| sim> set DS diag=4;1;32;005;;017 | |
| sim> set DS diag=4;1;32;005;;017 | |
| sim> set DS diag=1;1;0;013;S;000 | |
| sim> set DS diag=1;1;42;005;S;000 | |
| sim> set DS diag=1;1;43;005;P;000 | |
| sim> set DS diag=1;1;44;005;D;021 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=1;1;42;005;;017 | |
| sim> set DS diag=4;0;37;005;;017 | |
| sim> set CLK realtime | |
| sim> set DS0 7905,format | |
| sim> attach -n DS0 scratch.0.disc | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| D99 01 CARTRIDGE DISC (HP 30129A) DIAGNOSTIC CONFIGURATION (D419A.01.4) | |
| (C)COPYRIGHT HEWLETT PACKARD COMPANY 1976. | |
| Q99 02 DECIMAL DEVICE NUMBER? | |
| 4 | |
| Q99 03 MAXIMUM ERROR PRINT COUNT? | |
| 999 | |
| P99 55 UPDATE SWITCH REGISTER | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Q99 61 RESTART?(YES/NO) | |
| NO | |
| Q99 06 PRESENT SECTION REGISTER: %177000 DO YOU WISH TO CHANGE?(YES/NO) | |
| YES | |
| Q99 06 UPDATE SECTION REGISTER: % | |
| 177002 | |
| Q99 06 PRESENT SECTION REGISTER: %177002 DO YOU WISH TO CHANGE?(YES/NO) | |
| NO | |
| P99 51 RESET SWITCH 1 (CHANGE) | |
| sim> deposit SWCH 100001 | |
| sim> go | |
| P99 05 RESET BOTH PROT.DATA SWITCHES,SET SWITCH FORMAT AND SET UNIT TO 0 | |
| Q99 42 WISH TO EXECUTE INTERACTIVE PORTION IN SECTION 1 (YES/NO) | |
| YES | |
| D99 07 CARTRIDGE DISC (HP 30129A) DIAGNOSTIC OFF-LINE (D419A.01.4) | |
| Q18 68 DO YOU WISH FORMAT DISC? (YES/NO) | |
| NO | |
| P19 19 SET UPPER DATA PROTECT SWITCH | |
| sim> set DS0 protect=upper | |
| sim> go | |
| P19 27 RESET SWITCH FORMAT | |
| sim> set DS0 noformat | |
| sim> go | |
| P19 19 RESET UPPER DATA PROTECT SWITCH | |
| sim> set DS0 unprotect=upper | |
| sim> go | |
| P19 20 SET LOWER DATA PROTECT SWITCH | |
| sim> set DS0 protect=lower | |
| sim> go | |
| P19 26 SET SWITCH FORMAT | |
| sim> set DS0 format | |
| sim> go | |
| P19 19 SET UPPER DATA PROTECT SWITCH | |
| sim> set DS0 protect=upper | |
| sim> go | |
| P19 27 RESET SWITCH FORMAT | |
| sim> set DS0 noformat | |
| sim> go | |
| P19 05 RESET BOTH PROT.DATA SWITCHES,SET SWITCH FORMAT | |
| sim> set DS0 unprotect | |
| sim> set DS0 format | |
| sim> go | |
| P20 58 RESET RUN SWITCH AT UNIT 0 | |
| sim> set DS0 unload | |
| sim> step 1500000 | |
| Step expired, P: 041076 (CMPI 0) | |
| sim> go | |
| P20 58 SET RUN SWITCH AND WAIT UNTIL READY | |
| sim> set DS0 load | |
| sim> step 1000000 | |
| Step expired, P: 041076 (CMPI 0) | |
| sim> go | |
| D92 57 SHORT PASS 0001 | |
| CYL: HEAD0% HEAD1% HEAD2% (ERROR TABLES) | |
| UNIT0 UNIT1 UNIT2 UNIT3 UNIT4 UNIT5 UNIT6 UNIT7 | |
| 0000 0000 0000 0000 0000 0000 0000 0000 | |
| P92 47 PAUSE AT PASS 000001 | |
| TEST RESULT: Partially passed. | |
| TEST NOTES: The diagnostic overrides supply the expected status returns for | |
| the following steps, which test features (defective, spare, | |
| and protected tracks, and error correction) that are not | |
| currently simulated: | |
| * 07 Write to a sector of a defective track | |
| * 08 Read of a sector of a defective track | |
| * 11 Write to a sector of a spare track | |
| * 12 Read of a sector of a spare track | |
| * 15 Write to a sector of a protected track | |
| * 16 Read of a sector of a protected track | |
| * 24 Read of a sector with a correctable data error | |
| * 27 Read of a sector with a correctable data error | |
| * 31 Read of a sector with a correctable data error | |
| * 48 Read of a sector with a correctable data error | |
| * 50 Read of a sector with a correctable data error | |
| * 52 Read of a sector with a correctable data error | |
| * 62 Read of a sector on a spare, protected, and defective | |
| track | |
| * 66 Multiple retries for a read of a sector with a | |
| correctable data error | |
| * 77 An SIO program conditional jump on a correctable data | |
| error | |
| The step commands impose delays that are required by the | |
| diagnostic when testing head unload and load, which assumes that | |
| the user intervention will take longer than the 1.8 second | |
| controller timeout. The status returned should be Drive | |
| Attention after a head load, but the diagnostic expects Normal | |
| Completion, as the status is cleared whenever the controller | |
| times out. | |
| -------------------------------------------------- | |
| D419A - Cartridge Disc (multiple unit, short pass) | |
| -------------------------------------------------- | |
| TESTED DEVICE: DS (hp3000_ds.c) | |
| CONFIGURATION: sim> set CLK realtime | |
| sim> set DS0 7905,format | |
| sim> set DS1 7905,format | |
| sim> set DS2 7905,format | |
| sim> set DS3 7905,format | |
| sim> set DS4 7905,format | |
| sim> set DS5 7905,format | |
| sim> set DS6 7905,format | |
| sim> set DS7 7905,format | |
| sim> attach -n DS0 scratch.0.disc | |
| sim> attach -n DS1 scratch.1.disc | |
| sim> attach -n DS2 scratch.2.disc | |
| sim> attach -n DS3 scratch.3.disc | |
| sim> attach -n DS4 scratch.4.disc | |
| sim> attach -n DS5 scratch.5.disc | |
| sim> attach -n DS6 scratch.6.disc | |
| sim> attach -n DS7 scratch.7.disc | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| D99 01 CARTRIDGE DISC (HP 30129A) DIAGNOSTIC CONFIGURATION (D419A.01.4) | |
| (C)COPYRIGHT HEWLETT PACKARD COMPANY 1976. | |
| Q99 02 DECIMAL DEVICE NUMBER? | |
| 4 | |
| Q99 03 MAXIMUM ERROR PRINT COUNT? | |
| 999 | |
| P99 55 UPDATE SWITCH REGISTER | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Q99 61 RESTART?(YES/NO) | |
| NO | |
| Q99 06 PRESENT SECTION REGISTER: %177000 DO YOU WISH TO CHANGE?(YES/NO) | |
| YES | |
| Q99 06 UPDATE SECTION REGISTER: % | |
| 137402 | |
| Q99 06 PRESENT SECTION REGISTER: %137402 DO YOU WISH TO CHANGE?(YES/NO) | |
| NO | |
| P99 08 UNIT NUMBER TABLE | |
| 01 DRIVE(S);00 | |
| Q99 09 WISH TO ALTER TABLE? | |
| YES | |
| Q99 10 ENTER UNIT NUMBERS SEPARATED BY COMMAS | |
| 0,1,2,3,4,5,6,7 | |
| P99 08 UNIT NUMBER TABLE | |
| 08 DRIVE(S);00 01 02 03 04 05 06 07 | |
| Q99 09 WISH TO ALTER TABLE? | |
| NO | |
| P99 51 RESET SWITCH 1 (CHANGE) | |
| sim> deposit SWCH 100001 | |
| sim> go | |
| P99 05 RESET BOTH PROT.DATA SWITCHES,SET SWITCH FORMAT AND SET UNIT TO 0 | |
| Q99 42 WISH TO EXECUTE INTERACTIVE PORTION IN SECTION 1 (YES/NO) | |
| NO | |
| D99 07 CARTRIDGE DISC (HP 30129A) DIAGNOSTIC OFF-LINE (D419A.01.4) | |
| D92 57 SHORT PASS 0001 | |
| CYL: HEAD0% HEAD1% HEAD2% (ERROR TABLES) | |
| UNIT0 UNIT1 UNIT2 UNIT3 UNIT4 UNIT5 UNIT6 UNIT7 | |
| 0000 0000 0000 0000 0000 0000 0000 0000 | |
| P92 47 PAUSE AT PASS 000001 | |
| TEST RESULT: Partially passed. | |
| TEST NOTES: Section 1 is not selected to avoid specifying diagnostic | |
| overrides for features that are not currently simulated. | |
| -------------------------- | |
| D421 - Memory Pattern Test | |
| -------------------------- | |
| TESTED DEVICE: CPU (hp3000_cpu.c) | |
| CONFIGURATION: sim> go | |
| Programmed halt, CIR: 030376 (HALT 16), P: 015056 (RSW) | |
| sim> deposit SWCH 100011 | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| HP 3000 SERIES II MEMORY PATERN TEST D421A.01.0 | |
| (C)COPYRIGHT HEWLETT PACKARD COMPANY 1976. | |
| LOW BANK?0 | |
| LOW ADDRESS?020000 | |
| HIGH BANK?3 | |
| HIGH ADDRESS?177777 | |
| PASS # 000000 | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010255 (BR P-154) | |
| TEST RESULT: Passed. | |
| TEST NOTES: The diagnostic is only applicable to the Series II, so the | |
| highest memory bank that can be tested is bank 3. The Series | |
| III implemented its memory pattern test in microcode. | |
| --------------------------- | |
| D422A - Multiplexer Channel | |
| --------------------------- | |
| TESTED DEVICE: MPX (hp3000_chan.c) | |
| CONFIGURATION: sim> set scmb1 enable | |
| sim> set scmb2 enable | |
| sim> set scmb1 mx | |
| sim> set scmb2 mx | |
| sim> set clk realtime | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| DO1 30036A/B MPX CHANNEL TEST (HP D422A.01.2) | |
| (C)COPYRIGHT HEWLETT-PACKARD COMPANY 1978. | |
| Q01 SELECT SWITCH REGISTER OPTIONS | |
| Programmed halt, CIR: 030360 (HALT 0), P: 042614 (RSW) | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Q02 SELECT SECTION OPTIONS | |
| Programmed halt, CIR: 030361 (HALT 1), P: 042660 (LDI 1) | |
| sim> deposit SWCH 177777 | |
| sim> go | |
| Q03 RESTORE REGISTER OPTIONS | |
| Programmed halt, CIR: 030362 (HALT 2), P: 042667 (RSW) | |
| sim> deposit SWCH 100001 | |
| sim> go | |
| Q04 ENTER MPX DEVICE #= 127 | |
| Q05 ENTER MAXIMUM ERROR COUNT# = 999 | |
| P02 END SECTION IORES | |
| P02 END SECTION ARADDR | |
| P02 END SECTION ARDATA | |
| P02 END SECTION ARCPP | |
| P02 END SECTION ORADDR | |
| P02 END SECTION ORDATA | |
| P02 END SECTION ORCP | |
| P02 END SECTION AREG | |
| P02 END SECTION OREG | |
| P02 END SECTION NSGP1 | |
| P02 END SECTION NSGP2 | |
| P02 END SECTION NSGP3 | |
| P02 END SECTION NSGP4 | |
| P02 END SECTION STPAR | |
| P11 IF SEL. CHAN. MAINTENANCE BOARD ALREADY IN THEN HIT * CR* | |
| P11 OTHERWISE INSERT BOARD,CONNECT POLLS,AND RE-COLD LOAD | |
| Q06 ENTER SEL. CHAN. MAINTENANCE BOARD DRT# =65 | |
| Q07 ENTER 2ND SCMB DRT# = 66 | |
| Q08 ENTER CLOCK/CONSOLE DRT# = 3 | |
| Q09 ENTER UPPER BANK # (DECIMAL) = 7 | |
| P15 END SIO TEST CONFIGURATION | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 00; STEP 63 | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 01; STEP 63 | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 02; STEP 63 | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 03; STEP 63 | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 04; STEP 63 | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 05; STEP 63 | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 06; STEP 63 | |
| P16 FAST SR READ MODE(2K XFER); TIME = 4 MSEC.; BANK 07; STEP 63 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 00; STEP 68 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 01; STEP 68 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 02; STEP 68 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 03; STEP 68 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 04; STEP 68 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 05; STEP 68 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 06; STEP 68 | |
| P17 FAST SR WRITE MODE(2K XFER); TIME=4 MSEC.; BANK 07; STEP 68 | |
| P02 END SECTION SIOTST | |
| D02 END MPX CHAN TEST | |
| D03 END: PROGRAM CYCLE: PASS = 1 | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010175 (ZERO,NOP) | |
| TEST RESULT: Passed. | |
| -------------------------------------------- | |
| D426A - System Clock/Fault Logging Interface | |
| -------------------------------------------- | |
| TESTED DEVICE: CLK (hp3000_clk.c) | |
| CONFIGURATION: sim> set clk realtime | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| D01 HP SYSTEM CLOCK DIAGNOSTIC (D426A.00.00) | |
| (C)COPYRIGHT HEWLETT-PACKARD COMPANY 1978. | |
| Q02 SELECT SWREG OPTIONS | |
| Programmed halt, CIR: 030360 (HALT 0), P: 010022 (RSW) | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Q03 SELECT SECTION SWREG. OPTIONS | |
| Programmed halt, CIR: 030361 (HALT 1), P: 010066 (RSW) | |
| sim> deposit SWCH 074000 | |
| sim> go | |
| Q05 RESTORE SWREG OPTIONS | |
| Programmed halt, CIR: 030362 (HALT 2), P: 010075 (RSW) | |
| sim> deposit SWCH 100011 | |
| sim> go | |
| P01 SECTION 1 | |
| P03 END STEP 101 | |
| P03 END STEP 103 | |
| P03 END STEP 105 | |
| P02 END SECTION 1 | |
| P01 SECTION 2 | |
| P03 END STEP 202 | |
| P03 END STEP 203 | |
| P03 END STEP 204 | |
| P03 END STEP 205 | |
| P03 END STEP 206 | |
| P03 END STEP 207 | |
| P03 END STEP 210 | |
| P02 END SECTION 2 | |
| P01 SECTION 3 | |
| P03 END STEP 302 | |
| P03 END STEP 304 | |
| P03 END STEP 306 | |
| P03 END STEP 310 | |
| P03 END STEP 312 | |
| P03 END STEP 314 | |
| P03 END STEP 316 | |
| P02 END SECTION 3 | |
| P01 SECTION 4 | |
| P03 END STEP 402 | |
| P03 END STEP 404 | |
| P03 END STEP 406 | |
| P03 END STEP 407 | |
| P03 END STEP 410 | |
| P03 END STEP 411 | |
| P03 END STEP 412 | |
| P03 END STEP 413 | |
| P03 END STEP 414 | |
| P03 END STEP 415 | |
| P03 END STEP 422 | |
| P03 END STEP 424 | |
| P03 END STEP 426 | |
| P02 END SECTION 4 | |
| D02 END: PROGRAM CYCLE: PASS = 1 | |
| D03 HALT: COMPLETE PROGRAM CYCLE | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010300 (BR P-230) | |
| TEST RESULT: Passed. | |
| TEST NOTES: This diagnostic does not test the Fault Logging Interface. | |
| ------------------------------- | |
| D427A - Terminal Data Interface | |
| ------------------------------- | |
| TESTED DEVICE: ATCD (hp3000_atc.c) | |
| CONFIGURATION: sim> set atcd diag | |
| sim> set clk realtime | |
| sim> go | |
| TEST REPORT: Programmed halt, CIR: 030366 (HALT 6), P: 010764 (LRA P+4) | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Programmed halt, CIR: 030365 (HALT 5), P: 010215 (RSW) | |
| sim> deposit SWCH 077400 | |
| sim> go | |
| Programmed halt, CIR: 030366 (HALT 6), P: 010231 (BR P-47) | |
| sim> deposit SWCH 100011 | |
| sim> go | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010331 (BR P+7) | |
| TEST RESULT: Passed. | |
| ------------------------ | |
| D429A - Selector Channel | |
| ------------------------ | |
| TESTED DEVICE: SEL (hp3000_sel.c) | |
| CONFIGURATION: sim> set clk realtime | |
| sim> set scmb enable | |
| sim> set scmb sc | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| D100 HP30030B/C SELECTOR CHANNEL DIAG (D429A.01.01) | |
| (C)COPYRIGHT HEWLETT-PACKARD COMPANY 1978. | |
| Q104 SELECT OPTIONS | |
| Programmed halt, CIR: 030360 (HALT 0), P: 010033 (RSW) | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Q110 SELECT SECTION OPTIONS | |
| Programmed halt, CIR: 030361 (HALT 1), P: 010073 (RSW) | |
| sim> deposit SWCH 177400 | |
| sim> go | |
| Q111 RESTORE SELECT OPTIONS | |
| Programmed halt, CIR: 030362 (HALT 2), P: 010102 (RSW) | |
| sim> deposit SWCH 100011 | |
| sim> go | |
| Q101 SET MAINT CARD DEV NUM? 65 | |
| Q102 SET TIMER/CONSOLE DEV NUM? 3 | |
| Q108 ENTER UPPER BANK # (DECIMAL) = 7 | |
| Q105 ERR PRINT LIMIT? 999 | |
| D110 DIRECT I/O TEST | |
| D127 DIRECT I/O TEST COMPLETED | |
| D130 CONTROL ORDER TEST | |
| D217 CONTROL ORDER TEST COMPLETE | |
| D220 READ TEST | |
| D244 2K READ 1 MILLISEC; BANK00 | |
| D244 2K READ 1 MILLISEC; BANK01 | |
| D244 2K READ 1 MILLISEC; BANK02 | |
| D244 2K READ 1 MILLISEC; BANK03 | |
| D244 2K READ 1 MILLISEC; BANK04 | |
| D244 2K READ 1 MILLISEC; BANK05 | |
| D244 2K READ 1 MILLISEC; BANK06 | |
| D244 2K READ 1 MILLISEC; BANK07 | |
| D247 READ TEST COMPLETED | |
| D250 WRITE TEST | |
| D274 2K WRITE 1 MILLISEC; BANK00 | |
| D274 2K WRITE 1 MILLISEC; BANK01 | |
| D274 2K WRITE 1 MILLISEC; BANK02 | |
| D274 2K WRITE 1 MILLISEC; BANK03 | |
| D274 2K WRITE 1 MILLISEC; BANK04 | |
| D274 2K WRITE 1 MILLISEC; BANK05 | |
| D274 2K WRITE 1 MILLISEC; BANK06 | |
| D274 2K WRITE 1 MILLISEC; BANK07 | |
| D275 WRITE TEST COMPLETED | |
| D300 CHAINED READ TEST | |
| D317 CHAINED READ TEST COMPLETED | |
| D320 CHAINED WRITE TEST | |
| D337 CHAINED WRITE TEST COMPLETE | |
| D340 ERROR RESPONSE TEST | |
| D367 ERROR RESPONSE TEST COMPLETED | |
| D600 SELECTOR CHANNEL DIAG COMPLETE | |
| D601 END OF PASS 1 | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010427 (SED 0) | |
| TEST RESULT: Passed. | |
| ------------------------------------------ | |
| D429A - Selector Channel Maintenance Board | |
| ------------------------------------------ | |
| TESTED DEVICE: SCMB (hp3000_scmb.c) | |
| CONFIGURATION: sim> set clk realtime | |
| sim> set scmb1 enable | |
| sim> set scmb1 mx | |
| sim> set scmb2 enable | |
| sim> set scmb2 mx | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| D100 HP30030B/C SELECTOR CHANNEL DIAG (D429A.01.01) | |
| (C)COPYRIGHT HEWLETT-PACKARD COMPANY 1978. | |
| Q104 SELECT OPTIONS | |
| Programmed halt, CIR: 030360 (HALT 0), P: 010033 (RSW) | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Q110 SELECT SECTION OPTIONS | |
| Programmed halt, CIR: 030361 (HALT 1), P: 010073 (RSW) | |
| sim> deposit SWCH 177400 | |
| sim> go | |
| Q111 RESTORE SELECT OPTIONS | |
| Programmed halt, CIR: 030362 (HALT 2), P: 010102 (RSW) | |
| sim> deposit SWCH 101011 | |
| sim> go | |
| Q101 SET MAINT CARD DEV NUM? 65 | |
| Q102 SET TIMER/CONSOLE DEV NUM? 3 | |
| Q108 ENTER UPPER BANK # (DECIMAL) = 7 | |
| Q105 ERR PRINT LIMIT? 999 | |
| D110 DIRECT I/O TEST | |
| D127 DIRECT I/O TEST COMPLETED | |
| D130 CONTROL ORDER TEST | |
| D217 CONTROL ORDER TEST COMPLETE | |
| D220 READ TEST | |
| D244 2K READ 4 MILLISEC; BANK00 | |
| D244 2K READ 4 MILLISEC; BANK01 | |
| D244 2K READ 4 MILLISEC; BANK02 | |
| D244 2K READ 4 MILLISEC; BANK03 | |
| D244 2K READ 4 MILLISEC; BANK04 | |
| D244 2K READ 4 MILLISEC; BANK05 | |
| D244 2K READ 4 MILLISEC; BANK06 | |
| D244 2K READ 4 MILLISEC; BANK07 | |
| D247 READ TEST COMPLETED | |
| D250 WRITE TEST | |
| D274 2K WRITE 4 MILLISEC; BANK00 | |
| D274 2K WRITE 4 MILLISEC; BANK01 | |
| D274 2K WRITE 4 MILLISEC; BANK02 | |
| D274 2K WRITE 4 MILLISEC; BANK03 | |
| D274 2K WRITE 4 MILLISEC; BANK04 | |
| D274 2K WRITE 4 MILLISEC; BANK05 | |
| D274 2K WRITE 4 MILLISEC; BANK06 | |
| D274 2K WRITE 4 MILLISEC; BANK07 | |
| D275 WRITE TEST COMPLETED | |
| D300 CHAINED READ TEST | |
| D317 CHAINED READ TEST COMPLETED | |
| D320 CHAINED WRITE TEST | |
| D337 CHAINED WRITE TEST COMPLETE | |
| D340 ERROR RESPONSE TEST | |
| D367 ERROR RESPONSE TEST COMPLETED | |
| D600 SELECTOR CHANNEL DIAG COMPLETE | |
| D601 END OF PASS 1 | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010427 (SED 0) | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| D600 SELECTOR CHANNEL DIAG COMPLETE | |
| D601 END OF PASS 2 | |
| Q110 SELECT SECTION OPTIONS | |
| Programmed halt, CIR: 030361 (HALT 1), P: 010073 (RSW) | |
| sim> deposit SWCH 177400 | |
| sim> go | |
| Q111 RESTORE SELECT OPTIONS | |
| Programmed halt, CIR: 030362 (HALT 2), P: 010102 (RSW) | |
| sim> deposit SWCH 101011 | |
| sim> go | |
| Q101 SET MAINT CARD DEV NUM? 66 | |
| Q102 SET TIMER/CONSOLE DEV NUM? 3 | |
| Q108 ENTER UPPER BANK # (DECIMAL) = 7 | |
| Q105 ERR PRINT LIMIT? 999 | |
| D110 DIRECT I/O TEST | |
| D127 DIRECT I/O TEST COMPLETED | |
| D130 CONTROL ORDER TEST | |
| D217 CONTROL ORDER TEST COMPLETE | |
| D220 READ TEST | |
| D244 2K READ 4 MILLISEC; BANK00 | |
| D244 2K READ 4 MILLISEC; BANK01 | |
| D244 2K READ 4 MILLISEC; BANK02 | |
| D244 2K READ 4 MILLISEC; BANK03 | |
| D244 2K READ 4 MILLISEC; BANK04 | |
| D244 2K READ 4 MILLISEC; BANK05 | |
| D244 2K READ 4 MILLISEC; BANK06 | |
| D244 2K READ 4 MILLISEC; BANK07 | |
| D247 READ TEST COMPLETED | |
| D250 WRITE TEST | |
| D274 2K WRITE 4 MILLISEC; BANK00 | |
| D274 2K WRITE 4 MILLISEC; BANK01 | |
| D274 2K WRITE 4 MILLISEC; BANK02 | |
| D274 2K WRITE 4 MILLISEC; BANK03 | |
| D274 2K WRITE 4 MILLISEC; BANK04 | |
| D274 2K WRITE 4 MILLISEC; BANK05 | |
| D274 2K WRITE 4 MILLISEC; BANK06 | |
| D274 2K WRITE 4 MILLISEC; BANK07 | |
| D275 WRITE TEST COMPLETED | |
| D300 CHAINED READ TEST | |
| D317 CHAINED READ TEST COMPLETED | |
| D320 CHAINED WRITE TEST | |
| D337 CHAINED WRITE TEST COMPLETE | |
| D340 ERROR RESPONSE TEST | |
| D367 ERROR RESPONSE TEST COMPLETED | |
| D600 SELECTOR CHANNEL DIAG COMPLETE | |
| D601 END OF PASS 1 | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010427 (SED 0) | |
| TEST RESULT: Passed. | |
| ---------------------------------------------------- | |
| D433A - 7970B Nine-Track Magnetic Tape (single unit) | |
| ---------------------------------------------------- | |
| TESTED DEVICE: MS (hp3000_ms.c) | |
| CONFIGURATION: sim> set clk realtime | |
| sim> set ms0 7970B,reel=600 | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| HP 30115A 9-TRACK MAGNETIC TAPE (D433A.01.4) | |
| (STAND-ALONE DIAGNOSTIC PROGRAM) | |
| (C) COPYRIGHT HEWLETT-PACKARD COMPANY 1976. | |
| Q010 TAPE DEVICE NUMBER? 6 | |
| Q011 TIMER DEVICE NUMBER? 3 | |
| Q012 MAXIMUM ERROR PRINT COUNT? 100 | |
| P005 TYPE FOLLOWING CONTROL | |
| A'CR'-AUTO, R'CR'-RESTART, | |
| M'CR'-MANU, 'CR'-RESUME, YOUR CODE? A | |
| D015 PRESENT SECTION REGISTER:%077414 DO YOU WISH TO CHANGE?(YES/NO)YES | |
| D015 UPDATE SECTION REGISTER:%067400 | |
| D015 PRESENT SECTION REGISTER:%067400 DO YOU WISH TO CHANGE?(YES/NO)NO | |
| Q019 AUTO-PROCESS: ENTER TAPE UNIT(B,E,NO) AT | |
| Q020 DRIVE 0? B | |
| Q020 DRIVE 1? NO | |
| Q020 DRIVE 2? NO | |
| Q020 DRIVE 3? NO | |
| P003 UNLOAD PROGRAM TAPE - LOAD TEST TAPE(S) | |
| Q030 ALL DEFINITIONS CORRECT(YES/NO)? YES | |
| P011 UPDATE SWITCH REGISTER (CR) | |
| NEW INT.SW.REG 1 000 000 000 000 001 | |
| D031 TEST SECTION A01 COMPL. | |
| D031 TEST SECTION A02 COMPL. | |
| E274 STEP-0434 COMP. AND READ CRCC ARE DIFFER. | |
| E116 STEP-0434 EXPECT.- OBTAIN. CRCC | |
| 120200 032400 | |
| E274 STEP-0437 COMP. AND READ CRCC ARE DIFFER. | |
| E116 STEP-0437 EXPECT.- OBTAIN. CRCC | |
| 000310 032400 | |
| D065 000004 ERRORS IN SECTION 04 | |
| D066 000004 TOTAL ERRORS | |
| D031 TEST SECTION A04 COMPL. | |
| D031 TEST SECTION A05 COMPL. | |
| D031 TEST SECTION A06 COMPL. | |
| D031 TEST SECTION A07 COMPL. | |
| P060 01 PASS 000004 TOTAL ERRORS | |
| P010 PAUSE AT PASS 01 | |
| TEST RESULT: Partially passed. | |
| TEST NOTES: Section 3 (tape mark tests) is not selected, as the simulation | |
| does not provide the capability to write arbitrary data in each | |
| of the tape tracks and so cannot write or read bad tape marks. | |
| Steps 434 and 437 (read-after-write tests) fail, as the simulation | |
| does not provide the capability to write or ready arbitrary | |
| cyclic redundancy check characters (CRCCs). | |
| ------------------------------------------------------ | |
| D433A - 7970E Nine-Track Magnetic Tape (multiple unit) | |
| ------------------------------------------------------ | |
| TESTED DEVICE: MS (hp3000_ms.c) | |
| CONFIGURATION: sim> set clk realtime | |
| sim> set ms0 7970E,reel=600 | |
| sim> set ms1 7970E,reel=600 | |
| sim> set ms2 7970E,reel=600 | |
| sim> set ms3 7970E,reel=600 | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| HP 30115A 9-TRACK MAGNETIC TAPE (D433A.01.4) | |
| (STAND-ALONE DIAGNOSTIC PROGRAM) | |
| (C) COPYRIGHT HEWLETT-PACKARD COMPANY 1976. | |
| Q010 TAPE DEVICE NUMBER? 6 | |
| Q011 TIMER DEVICE NUMBER? 3 | |
| Q012 MAXIMUM ERROR PRINT COUNT? 100 | |
| P005 TYPE FOLLOWING CONTROL | |
| A'CR'-AUTO, R'CR'-RESTART, | |
| M'CR'-MANU, 'CR'-RESUME, YOUR CODE? A | |
| D015 PRESENT SECTION REGISTER:%077414 DO YOU WISH TO CHANGE?(YES/NO)YES | |
| D015 UPDATE SECTION REGISTER:%077400 | |
| D015 PRESENT SECTION REGISTER:%077400 DO YOU WISH TO CHANGE?(YES/NO)NO | |
| Q019 AUTO-PROCESS: ENTER TAPE UNIT(B,E,NO) AT | |
| Q020 DRIVE 0? E | |
| Q020 DRIVE 1? E | |
| Q020 DRIVE 2? E | |
| Q020 DRIVE 3? E | |
| P003 UNLOAD PROGRAM TAPE - LOAD TEST TAPE(S) | |
| [CTRL+E] | |
| sim> attach -n ms0 scratch.0.tape | |
| sim> attach -n ms1 scratch.1.tape | |
| sim> attach -n ms2 scratch.2.tape | |
| sim> attach -n ms3 scratch.3.tape | |
| sim> go | |
| Q030 ALL DEFINITIONS CORRECT(YES/NO)? YES | |
| P011 UPDATE SWITCH REGISTER (CR) | |
| [CTRL+E] | |
| sim> deposit SWCH 100011 | |
| sim> set ms realtime | |
| sim> go | |
| NEW INT.SW.REG 1 000 000 000 001 001 | |
| D031 TEST SECTION A01 COMPL. | |
| D031 TEST SECTION A02 COMPL. | |
| D031 TEST SECTION A03 COMPL. | |
| D031 TEST SECTION A04 COMPL. | |
| D031 TEST SECTION A05 COMPL. | |
| D031 TEST SECTION A06 COMPL. | |
| D031 TEST SECTION A07 COMPL. | |
| P060 01 PASS 000000 TOTAL ERRORS | |
| P010 PAUSE AT PASS 01 | |
| TEST RESULT: Passed. | |
| --------------------------------------------------------- | |
| D433A - 7970E Nine-Track Magnetic Tape (user interaction) | |
| --------------------------------------------------------- | |
| TESTED DEVICE: MS (hp3000_ms.c) | |
| CONFIGURATION: sim> set clk realtime | |
| sim> set ms0 7970E,reel=600 | |
| sim> go | |
| TEST REPORT: [CR entered] | |
| HP 30115A 9-TRACK MAGNETIC TAPE (D433A.01.4) | |
| (STAND-ALONE DIAGNOSTIC PROGRAM) | |
| (C) COPYRIGHT HEWLETT-PACKARD COMPANY 1976. | |
| Q010 TAPE DEVICE NUMBER? 6 | |
| Q011 TIMER DEVICE NUMBER? 3 | |
| Q012 MAXIMUM ERROR PRINT COUNT? 100 | |
| P005 TYPE FOLLOWING CONTROL | |
| A'CR'-AUTO, R'CR'-RESTART, | |
| M'CR'-MANU, 'CR'-RESUME, YOUR CODE? M | |
| D015 PRESENT SECTION REGISTER:%077414 DO YOU WISH TO CHANGE?(YES/NO)YES | |
| D015 UPDATE SECTION REGISTER:%000014 | |
| D015 PRESENT SECTION REGISTER:%000014 DO YOU WISH TO CHANGE?(YES/NO)NO | |
| P015 MANU PROCES: UPDATE SWITCH REGISTER (CR) | |
| NEW INT.SW.REG 1 000 000 000 001 001 | |
| P019 ON-LINE/RESET TEST | |
| P026 LOAD TAPE(RING), PUSH RESET, OFF AND TYPE RESPONSE 'CR' | |
| sim> attach -n ms0 scratch.tape | |
| sim> set ms0 offline | |
| sim> go | |
| P027 PUSH DRIVE 0, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> set ms0 online | |
| sim> go | |
| P028 PUSH RESET, OFF AND TYPE RESPONSE 'CR' | |
| sim> set ms0 offline | |
| sim> go | |
| P027 PUSH DRIVE 1, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> detach ms0 | |
| sim> attach ms1 scratch.tape | |
| sim> go | |
| P028 PUSH RESET, OFF AND TYPE RESPONSE 'CR' | |
| sim> set ms1 offline | |
| sim> go | |
| P027 PUSH DRIVE 2, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> detach ms1 | |
| sim> attach ms2 scratch.tape | |
| sim> go | |
| P028 PUSH RESET, OFF AND TYPE RESPONSE 'CR' | |
| sim> set ms2 offline | |
| sim> go | |
| P027 PUSH DRIVE 3, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> detach ms2 | |
| sim> attach ms3 scratch.tape | |
| sim> go | |
| P028 PUSH RESET, OFF AND TYPE RESPONSE 'CR' | |
| sim> set ms3 offline | |
| sim> go | |
| P029 LOAD TAPE(RING), PUSH OFF,RESET, ON-LINE AND | |
| P056 TYPE SELECTED DRIVE ? | |
| sim> detach ms3 | |
| sim> attach ms0 scratch.tape | |
| sim> set ms0 offline | |
| sim> go | |
| 0 | |
| P038 PUSH DRIVE 0 BUTTON & TYPE RESPONSE 'CR' | |
| sim> set ms0 online | |
| sim> go | |
| P039 CHECK LIGHT RESET, PUSH ON-LINE AND RESPOND | |
| sim> set ms0 online | |
| sim> go | |
| P029 LOAD TAPE(RING), PUSH OFF,RESET, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> set ms0 offline | |
| sim> go | |
| P030 CHECK LIGHT WRITE-ENABLE, PUSH DRIVE 0 AND TYPE RESPONSE 'CR' | |
| sim> set ms0 online | |
| sim> go | |
| P030 CHECK LIGHT WRITE-ENABLE, PUSH DRIVE 1 AND TYPE RESPONSE 'CR' | |
| sim> detach ms0 | |
| sim> attach ms1 scratch.tape | |
| sim> go | |
| P030 CHECK LIGHT WRITE-ENABLE, PUSH DRIVE 2 AND TYPE RESPONSE 'CR' | |
| sim> detach ms1 | |
| sim> attach ms2 scratch.tape | |
| sim> go | |
| P030 CHECK LIGHT WRITE-ENABLE, PUSH DRIVE 3 AND TYPE RESPONSE 'CR' | |
| sim> detach ms2 | |
| sim> attach ms3 scratch.tape | |
| sim> go | |
| P029 LOAD TAPE(RING), PUSH OFF,RESET, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> detach ms3 | |
| sim> attach ms0 scratch.tape | |
| sim> set ms0 offline | |
| sim> go | |
| P032 PUSH DRIVE 0 AND TYPE RESPONSE 'CR' | |
| sim> set ms0 online | |
| sim> go | |
| P033 PUSH RESET, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> set ms0 offline | |
| sim> set ms0 online | |
| sim> go | |
| P032 PUSH DRIVE 1 AND TYPE RESPONSE 'CR' | |
| sim> detach ms0 | |
| sim> attach ms1 scratch.tape | |
| sim> go | |
| P033 PUSH RESET, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> set ms1 offline | |
| sim> set ms1 online | |
| sim> go | |
| P032 PUSH DRIVE 2 AND TYPE RESPONSE 'CR' | |
| sim> detach ms1 | |
| sim> attach ms2 scratch.tape | |
| sim> go | |
| P033 PUSH RESET, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> set ms2 offline | |
| sim> set ms2 online | |
| sim> go | |
| P032 PUSH DRIVE 3 AND TYPE RESPONSE 'CR' | |
| sim> detach ms2 | |
| sim> attach ms3 scratch.tape | |
| sim> go | |
| P033 PUSH RESET, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> set ms3 offline | |
| sim> set ms3 online | |
| sim> go | |
| P034 PUT TAPE(RING), PUSH OFF, RESET AND RESPOND 'CR' | |
| sim> detach ms3 | |
| sim> attach ms0 scratch.tape | |
| sim> set ms0 offline | |
| sim> go | |
| P035 PUSH ON-LINE, DRIVE 0 AND TAPE RESPONSE 'CR' | |
| sim> set ms0 online | |
| sim> go | |
| P036 PUSH RESET AND TYPE RESPONSE 'CR' | |
| sim> set ms0 offline | |
| sim> go | |
| P035 PUSH ON-LINE, DRIVE 1 AND TAPE RESPONSE 'CR' | |
| sim> detach ms0 | |
| sim> attach ms1 scratch.tape | |
| sim> go | |
| P036 PUSH RESET AND TYPE RESPONSE 'CR' | |
| sim> set ms1 offline | |
| sim> go | |
| P035 PUSH ON-LINE, DRIVE 2 AND TAPE RESPONSE 'CR' | |
| sim> detach ms1 | |
| sim> attach ms2 scratch.tape | |
| sim> go | |
| P036 PUSH RESET AND TYPE RESPONSE 'CR' | |
| sim> set ms2 offline | |
| sim> go | |
| P035 PUSH ON-LINE, DRIVE 3 AND TAPE RESPONSE 'CR' | |
| sim> detach ms2 | |
| sim> attach ms3 scratch.tape | |
| sim> go | |
| P036 PUSH RESET AND TYPE RESPONSE 'CR' | |
| sim> set ms3 offline | |
| sim> go | |
| P037 FSR/BSR-TEST: TYPE DRIVE NUMBER AND 'CR'(EXECUTE) OR 'CR'(EXIT)0 | |
| P029 LOAD TAPE(RING), PUSH OFF,RESET, ON-LINE AND TYPE RESPONSE 'CR' | |
| sim> detach ms3 | |
| sim> attach ms0 scratch.tape | |
| sim> set ms0 offline | |
| sim> go | |
| P035 PUSH ON-LINE, DRIVE 0 AND TAPE RESPONSE 'CR' | |
| sim> set ms0 online | |
| sim> go | |
| D031 TEST SECTION M12 COMPL. | |
| P056 TYPE SELECTED DRIVE ? 0 | |
| P041 LOAD TAPE(RING), PUSH DRIVE 0 AND TYPE RESPONSE 'CR | |
| sim> attach -n ms0 scratch.tape | |
| sim> go | |
| P042 REMOVE RING FROM REEL, PUT IT BACK AND TYPE RESPONSE 'CR' | |
| sim> detach ms0 | |
| sim> attach -r ms0 scratch.tape | |
| sim> go | |
| P043 PUT RING BACK TO REEL, LOAD IT AND TYPE 'CR'(RESPONSE) | |
| sim> detach ms0 | |
| sim> attach ms0 scratch.tape | |
| sim> go | |
| D031 TEST SECTION M13 COMPL. | |
| P060 01 PASS 000000 TOTAL ERRORS | |
| P010 PAUSE AT PASS 01 | |
| TEST RESULT: Passed. | |
| --------------------------- | |
| D435A - Universal Interface | |
| --------------------------- | |
| TESTED DEVICE: LP (hp3000_lp.c) | |
| CONFIGURATION: sim> set lp diagnostic,intmask=8 | |
| sim> set clk realtime | |
| sim> go | |
| TEST REPORT: D100 UNIV. INTERFACE TEST (HP D435A.01.01) | |
| (C)COPYRIGHT HEWLETT PACKARD COMPANY 1976. | |
| ****************** WARNING ****************** | |
| this diagnostic has tests which will produce error | |
| conditions on interface boards which have datecodes | |
| PRIOR TO 1504. | |
| Q110 DEVICE NUMBER? 14 | |
| Q112 INTERRUPT MASK? 8 | |
| Q113 NEGATIVE TRUE? NO | |
| Q114 CHANGE INTERNAL SWITCH REGISTER? ? YES | |
| P114 INTERNAL SWITCH REGISTER | |
| Programmed halt, CIR: 030366 (HALT 6), P: 026015 (DDEL,DDEL) | |
| sim> deposit SWCH 100111 | |
| sim> go | |
| Q115 SECTION LIST? | |
| Q116 READER-PUNCH INTERFACE ? NO | |
| D102 END SECTION 0 | |
| D100 UNIV. INTERFACE TEST (HP D435A.01.01) | |
| (C)COPYRIGHT HEWLETT PACKARD COMPANY 1976. | |
| ****************** WARNING ****************** | |
| this diagnostic has tests which will produce error | |
| conditions on interface boards which have datecodes | |
| PRIOR TO 1504. | |
| P120 CONT6 ON, REST OFF | |
| Programmed halt, CIR: 030367 (HALT 7), P: 022145 (DDEL,DDEL) | |
| sim> assert LP CONT=10000 | |
| sim> go | |
| P120 CONT7 ON, REST OFF | |
| Programmed halt, CIR: 030367 (HALT 7), P: 022145 (DDEL,DDEL) | |
| sim> assert LP CONT=01000 | |
| sim> go | |
| P120 CONT8 ON, REST OFF | |
| Programmed halt, CIR: 030367 (HALT 7), P: 022145 (DDEL,DDEL) | |
| sim> assert LP CONT=00100 | |
| sim> go | |
| P120 CONT9 ON, REST OFF | |
| Programmed halt, CIR: 030367 (HALT 7), P: 022145 (DDEL,DDEL) | |
| sim> assert LP CONT=00010 | |
| sim> go | |
| P120 CONT10 ON, REST OFF | |
| Programmed halt, CIR: 030367 (HALT 7), P: 022145 (DDEL,DDEL) | |
| sim> assert LP CONT=00001 | |
| sim> go | |
| P121 JUMPER J2W1 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0000000001 | |
| sim> go | |
| P121 JUMPER J2W2 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0000000010 | |
| sim> go | |
| P121 JUMPER J2W3 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0000000100 | |
| sim> go | |
| P121 JUMPER J2W4 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0000001000 | |
| sim> go | |
| P121 JUMPER J2W5 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0000010000 | |
| sim> go | |
| P121 JUMPER J2W6 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0000100000 | |
| sim> go | |
| P121 JUMPER J2W7 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0001000000 | |
| sim> go | |
| P121 JUMPER J2W8 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0010000000 | |
| sim> go | |
| P121 JUMPER J2W9 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=0100000000 | |
| sim> go | |
| P121 JUMPER J2W10 LOW, REST HIGH | |
| Programmed halt, CIR: 030370 (HALT 10), P: 022056 (DDEL,DDEL) | |
| sim> assert LP J2WX=1000000000 | |
| sim> go | |
| P122 DEVICE END ASSERTED | |
| Programmed halt, CIR: 030371 (HALT 11), P: 021505 (DDEL,DDEL) | |
| sim> assert LP DEVEND=1 | |
| sim> go | |
| P124 BIT 0 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=100000 | |
| sim> go | |
| P124 BIT 1 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=040000 | |
| sim> go | |
| P124 BIT 2 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=020000 | |
| sim> go | |
| P124 BIT 3 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=010000 | |
| sim> go | |
| P124 BIT 4 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=004000 | |
| sim> go | |
| P124 BIT 5 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=002000 | |
| sim> go | |
| P124 BIT 6 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=001000 | |
| sim> go | |
| P124 BIT 7 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000400 | |
| sim> go | |
| P124 BIT 8 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000200 | |
| sim> go | |
| P124 BIT 9 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000100 | |
| sim> go | |
| P124 BIT 10 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000040 | |
| sim> go | |
| P124 BIT 11 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000020 | |
| sim> go | |
| P124 BIT 12 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000010 | |
| sim> go | |
| P124 BIT 13 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000004 | |
| sim> go | |
| P124 BIT 14 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000002 | |
| sim> go | |
| P124 BIT 15 HIGH, REST LOW | |
| Programmed halt, CIR: 030373 (HALT 13), P: 021407 (DDEL,DDEL) | |
| sim> assert LP READ=000001 | |
| sim> go | |
| D102 END SECTION 1 | |
| D102 END SECTION 2 | |
| D102 END SECTION 3 | |
| D102 END SECTION 4 | |
| D102 END SECTION 5 | |
| D102 END SECTION 6 | |
| D102 END SECTION 7 | |
| D102 END SECTION 8 | |
| D102 END SECTION 9 | |
| D102 END SECTION 10 | |
| P103 PASS 1 | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010265 (DDEL,DDEL) | |
| TEST RESULT: Passed. | |
| TEST NOTES: The interrupt mask number is changed from "E" (always enabled) to | |
| a numeric value to allow the mask circuits to be tested. | |
| ---------------------------------- | |
| D438A - Terminal Control Interface | |
| ---------------------------------- | |
| TESTED DEVICE: ATCC (hp3000_atc.c) | |
| CONFIGURATION: sim> set atcc diag | |
| sim> set clk realtime | |
| sim> go | |
| TEST REPORT: Programmed halt, CIR: 030366 (HALT 6), P: 010670 (LRA P+4) | |
| sim> deposit SWCH 140000 | |
| sim> go | |
| Programmed halt, CIR: 030365 (HALT 5), P: 010073 (RSW) | |
| sim> deposit SWCH 074000 | |
| sim> go | |
| Programmed halt, CIR: 030366 (HALT 6), P: 010107 (BR P-47) | |
| sim> deposit SWCH 100011 | |
| sim> go | |
| Programmed halt, CIR: 030375 (HALT 15), P: 010225 (BR P+7) | |
| TEST RESULT: Passed. | |
| ------------------------------------ | |
| D466A - Online Line Printer Verifier | |
| ------------------------------------ | |
| TESTED DEVICE: LP (hp3000_lp.c) | |
| CONFIGURATION: :STOPSPOOL 6 | |
| :RUN PD466A.HP32230.SUPPORT | |
| TEST REPORT: D1 ONLINE LINE PRINTER VERIFIER (HP D466A.01.06) | |
| (C) COPYRIGHT HEWLETT-PACKARD COMPANY 1978. | |
| PRINTER MUST BE SET TO 6 LINES PER INCH | |
| Q1 WHICH MODEL? 2607/08/10/13/14/17/18/19: 2617 | |
| Q2 64/96 CHARACTER SET?96 | |
| Q3 LOGICAL DEVICE ?6 | |
| Q4 FLAGS? | |
| PRESS 'ON/OFF' LINE SWITCH 'ON' THEN 'OFF' | |
| D7 PRESS 'CR' TO CONTINUE | |
| [CTRL+E] | |
| Simulation stopped, P: 071144 (PAUS 0) | |
| sim> set lp offline | |
| sim> go | |
| 19:44/3/LDEV #6 NOT READY | |
| COMPUTER CONSOLE SHOULD PRINT 'IO/X:XX/LDEV# XXX NOT READY' | |
| PRESS 'ON/OFF' SWITCH 'ON' | |
| D7 PRESS 'CR' TO CONTINUE | |
| [CTRL+E] | |
| Simulation stopped, P: 071144 (PAUS 0) | |
| sim> set lp online | |
| sim> go | |
| D6 END OF SECTION 1 | |
| D6 END OF SECTION 2 | |
| D6 END OF SECTION 3 | |
| D6 END OF SECTION 4 | |
| D6 END OF SECTION 5 | |
| D6 END OF SECTION 6 | |
| D6 END OF SECTION 7 | |
| LINE PRINTER VERIFIER TEST TERMINATED | |
| END OF PROGRAM | |
| TEST RESULT: Passed. | |
| TEST NOTES: The test was run from the OPERATOR.SYS account on MPE-V/R | |
| release E.01.00. |