Rivoreo Source Code Repositories
src.rivoreo.one / emulators / simh / 1e704bf185a35370a38f251f59e7578c7d477163 / . / HP2100 / hp2100_ds.c
blob: a769b0ba64546edc64d1b4889e95f528d0988f92 [file] [log] [blame] [raw]
/* hp2100_ds.c: HP 2100 13037 disk controller simulator
Copyright (c) 2004-2005, Robert M. Supnik
Permission is hereby granted, free of charge, to any person obtaining a
copy of this software and associated documentation files (the "Software"),
to deal in the Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute, sublicense,
and/or sell copies of the Software, and to permit persons to whom the
Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in
all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
ROBERT M SUPNIK BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of Robert M Supnik shall not be
used in advertising or otherwise to promote the sale, use or other dealings
in this Software without prior written authorization from Robert M Supnik.
ds 13037 disk controller
18-Mar-05 RMS Added attached test to detach routine
01-Mar-05 JDB Added SET UNLOAD/LOAD
States of the controller: the controller uP runs all the time, but most of
the time it is waiting for an event. The simulator only 'runs' the controller
when there's an event to process: change in CPU interface state, change in
disk state, or timeout. The controller has three states:
- Idle. No operations other than seek or recalibrate are in progress, and
the CPU interface is disconnected. The controller responds both to new
commands and to drive attention interrupts.
- Wait. No operations other than seek or recalibrate are in progress, but
the CPU interface is connected. The controller responds to new commands
but not to drive attention interrupts.
- Busy. The controller is processing a command. The controller does not
respond to new commands or to drive attention interrupts.
The controller busy state is loosely related to the testable (visible) busy
flop. If the visible busy flop is set, the controller is in the busy state;
but the controller can also be busy (processing an invalid opcode or invalid
unit) while visible busy is clear.
Omissions: the following features are not implemented:
- Drive hold. Since this is a single CPU implementation, the drives are
always available to the CPU.
- Spare, defective, protected. The disk files carry only data.
- Formatting. The disk files carry only data.
- ECC. Data errors are always uncorrectable.
Reference:
- 13037 Disc Controller Technical Information Package (13037-90902, Aug-1980)
*/
#include "hp2100_defs.h"
#include <math.h>
#define DS_NUMDR 8 /* max drives */
#define DS_DRMASK (DS_NUMDR - 1)
#define DS_NUMWD 128 /* data words/sec */
#define DS_NUMWDF 138 /* total words/sec */
#define DS_FSYNC 0 /* sector offsets */
#define DS_FCYL 1
#define DS_FHS 2
#define DS_FDATA 3
#define DS_FIFO_SIZE 16 /* fifo size */
#define DS_FIFO_EMPTY (ds_fifo_cnt == 0)
#define ds_ctrl ds_unit[DS_NUMDR] /* ctrl thread */
#define ds_timer ds_unit[DS_NUMDR + 1] /* timeout thread */
#define GET_CURSEC(x,d) ((int32) fmod (sim_gtime() / ((double) (x)), \
((double) (drv_tab[d].sc))))
/* Flags in the unit flags word */
#define UNIT_V_WLK (UNIT_V_UF + 0) /* write locked */
#define UNIT_V_UNLOAD (UNIT_V_UF + 1) /* heads unloaded */
#define UNIT_V_DTYPE (UNIT_V_UF + 2) /* disk type */
#define UNIT_M_DTYPE 3
#define UNIT_V_AUTO (UNIT_V_UF + 4) /* autosize */
#define UNIT_V_FMT (UNIT_V_UF + 5) /* format enabled */
#define UNIT_WLK (1 << UNIT_V_WLK)
#define UNIT_FMT (1 << UNIT_V_FMT)
#define UNIT_DTYPE (UNIT_M_DTYPE << UNIT_V_DTYPE)
#define UNIT_AUTO (1 << UNIT_V_AUTO)
#define UNIT_UNLOAD (1 << UNIT_V_UNLOAD)
#define GET_DTYPE(x) (((x) >> UNIT_V_DTYPE) & UNIT_M_DTYPE)
#define UNIT_WPR (UNIT_WLK | UNIT_RO) /* write prot */
/* Parameters in the unit descriptor */
#define FNC u3 /* function */
#define CYL u4 /* current cylinder */
#define STA u5 /* status */
/* Arguments to subroutines */
#define CLR_BUSY 0 /* clear visible busy */
#define SET_BUSY 1 /* set visible busy */
/* Command word - <12:8> are opcode, <7:0> are opcode dependent
cold load read <7:6> = head
<5:0> = sector
set file mask <7:4> = retry count
<3:0> = file mask (auto-seek options)
commands with units <7> = hold flag
<4:0> = unit number */
#define DSC_V_OP 8 /* opcode */
#define DSC_M_OP 037
#define DSC_COLD 000 /* cold load read */
#define DSC_RECAL 001 /* recalibrate */
#define DSC_SEEK 002 /* seek */
#define DSC_RSTA 003 /* request status */
#define DSC_RSA 004 /* request sector addr */
#define DSC_READ 005 /* read */
#define DSC_RFULL 006 /* read full */
#define DSC_VFY 007 /* verify */
#define DSC_WRITE 010 /* write */
#define DSC_WFULL 011 /* write full */
#define DSC_CLEAR 012 /* clear */
#define DSC_INIT 013 /* initialize */
#define DSC_AREC 014 /* address record */
#define DSC_RSYN 015 /* request syndrome */
#define DSC_ROFF 016 /* read with offset */
#define DSC_SFM 017 /* set file mask */
#define DSC_RNOVFY 022 /* read no verify */
#define DSC_WTIO 023 /* write TIO */
#define DSC_RDA 024 /* request disk addr */
#define DSC_END 025 /* end */
#define DSC_WAKE 026 /* wakeup */
#define DSC_ATN 035 /* pseudo: ATN */
#define DSC_BADU 036 /* pseudo: bad unit */
#define DSC_BADF 037 /* pseudo: bad opcode */
#define DSC_NEXT 0040 /* state increment */
#define DSC_2ND 0040 /* subcommand states */
#define DSC_3RD 0100
#define DSC_4TH 0140
#define DSC_V_CHD 6 /* cold load head */
#define DSC_M_CHD 03
#define DSC_V_CSC 0 /* cold load sector */
#define DSC_M_CSC 077
#define DSC_V_RTY 4 /* retry count */
#define DSC_M_RTY 017
#define DSC_V_DECR 3 /* seek decrement */
#define DSC_V_SPEN 2 /* enable sparing */
#define DSC_V_CYLM 1 /* cylinder mode */
#define DSC_V_AUTO 0 /* auto seek */
#define DSC_V_HOLD 7 /* hold flag */
#define DSC_V_UNIT 0 /* unit */
#define DSC_M_UNIT 017
#define DSC_V_SPAR 15 /* INIT spare */
#define DSC_V_PROT 14 /* INIT protected */
#define DSC_V_DFCT 13 /* INIT defective */
#define DSC_HOLD (1u << DSC_V_HOLD)
#define DSC_DECR (1u << DSC_V_DECR)
#define DSC_SPEN (1u << DSC_V_SPEN)
#define DSC_CYLM (1u << DSC_V_CYLM)
#define DSC_AUTO (1u << DSC_V_AUTO)
#define DSC_FMASK ((DSC_M_RTY << DSC_V_RTY)|DSC_DECR|\
DSC_SPEN|DSC_CYLM|DSC_AUTO)
#define DSC_GETOP(x) (((x) >> DSC_V_OP) & DSC_M_OP)
#define DSC_GETUNIT(x) (((x) >> DSC_V_UNIT) & DSC_M_UNIT)
#define DSC_GETCHD(x) (((x) >> DSC_V_CHD) & DSC_M_CHD)
#define DSC_GETCSC(x) (((x) >> DSC_V_CSC) & DSC_M_CSC)
#define DSC_SPAR (1u << DSC_V_SPAR)
#define DSC_PROT (1u << DSC_V_PROT)
#define DSC_DFCT (1u << DSC_V_DFCT)
/* Command flags */
#define CMF_UNDF 001 /* undefined */
#define CMF_CLREC 002 /* clear eoc flag */
#define CMF_CLRS 004 /* clear status */
#define CMF_UIDLE 010 /* requires unit no */
/* Cylinder words - 16b */
/* Head/sector word */
#define DSHS_V_HD 8 /* head */
#define DSHS_M_HD 037
#define DSHS_V_SC 0 /* sector */
#define DSHS_M_SC 0377
#define DSHS_HD (DSHS_M_HD << DSHS_V_HD)
#define DSHS_SC (DSHS_M_SC << DSHS_V_SC)
#define DSHS_GETHD(x) (((x) >> DSHS_V_HD) & DSHS_M_HD)
#define DSHS_GETSC(x) (((x) >> DSHS_V_SC) & DSHS_M_SC)
/* Status 1 */
#define DS1_V_SPAR 15 /* spare - na */
#define DS1_V_PROT 14 /* protected - na */
#define DS1_V_DFCT 13 /* defective - na */
#define DS1_V_STAT 8 /* status */
#define DS1_OK (000 << DS1_V_STAT) /* normal */
#define DS1_ILLOP (001 << DS1_V_STAT) /* illegal opcode */
#define DS1_AVAIL (002 << DS1_V_STAT) /* available */
#define DS1_CYLCE (007 << DS1_V_STAT) /* cyl compare err */
#define DS1_UNCOR (010 << DS1_V_STAT) /* uncor data err */
#define DS1_HSCE (011 << DS1_V_STAT) /* h/s compare err */
#define DS1_IOPE (012 << DS1_V_STAT) /* IO oper err - na */
#define DS1_EOCYL (014 << DS1_V_STAT) /* end cylinder */
#define DS1_OVRUN (016 << DS1_V_STAT) /* overrun */
#define DS1_CORDE (017 << DS1_V_STAT) /* correctible - na */
#define DS1_ILLST (020 << DS1_V_STAT) /* illegal spare - na */
#define DS1_DEFTK (021 << DS1_V_STAT) /* defective trk - na */
#define DS1_ACCER (022 << DS1_V_STAT) /* access not rdy - na */
#define DS1_S2ERR (023 << DS1_V_STAT) /* status 2 error */
#define DS1_TKPER (026 << DS1_V_STAT) /* protected trk - na */
#define DS1_UNAVL (027 << DS1_V_STAT) /* illegal unit */
#define DS1_ATN (037 << DS1_V_STAT) /* attention */
#define DS1_V_UNIT 0
#define DS1_SPAR (1u << DS1_V_SPAR)
#define DS1_PROT (1u << DS1_V_PROT)
#define DS1_DFCT (1u << DS1_V_DFCT)
/* Status 2, ^ = kept in unit status, * = dynamic */
#define DS2_ERR 0100000 /* *error */
#define DS2_V_ID 9 /* drive type */
#define DS2_ATN 0000200 /* ^attention */
#define DS2_RO 0000100 /* *read only */
#define DS2_FRM 0000040 /* *format */
#define DS2_FLT 0000020 /* fault - na */
#define DS2_FS 0000010 /* ^first status */
#define DS2_SC 0000004 /* ^seek error */
#define DS2_NR 0000002 /* *not ready */
#define DS2_BS 0000001 /* *busy */
#define DS2_ALLERR (DS2_FLT|DS2_SC|DS2_NR|DS2_BS)
/* Controller state */
#define DS_IDLE 0 /* idle */
#define DS_WAIT 1 /* command wait */
#define DS_BUSY 2 /* busy */
/* This controller supports four different disk drive types:
type #sectors/ #surfaces/ #cylinders/
surface cylinder drive
7905 48 3 411 =15MB
7906 48 4 411 =20MB
7920 48 5 823 =50MB
7925 64 9 823 =120MB
In theory, each drive can be a different type. The size field in
each unit selects the drive capacity for each drive and thus the
drive type. DISKS MUST BE DECLARED IN ASCENDING SIZE.
The 7905 and 7906 have fixed and removable platters. Consequently,
they are almost always accessed with cylinders limited to each
platter. The 7920 and 7925 have multiple-platter packs, and so are
almost always accessed with cylinders that span all surfaces.
Disk image files are arranged as a linear set of tracks. To improve
locality, tracks on the 7905 and 7906 images are grouped per-platter,
i.e., all tracks on heads 0 and 1, followed by all tracks on head 2
(and, for the 7906, head 3), whereas tracks on the 7920 and 7925 are
sequential by cylinder and head number.
This variable-access geometry is accomplished by defining a "heads
per cylinder" value for the fixed and removable sections of each
drive that indicates the number of heads that should be grouped for
locality. The removable values are set to 2 on the 7905 and 7906,
indicating that those drives typically use cylinders of two surfaces.
They are set to the number of surfaces per drive for the 7920 and
7925, as those typically use cylinders encompassing the entire
spindle.
*/
#define GET_DA(x,y,z,t) \
(((((y) < drv_tab[t].rh)? \
(x) * drv_tab[t].rh + (y): \
drv_tab[t].cyl * drv_tab[t].rh + \
((x) * drv_tab[t].fh + (y) - drv_tab[t].rh)) * \
drv_tab[t].sc + (z)) * DS_NUMWD)
#define D7905_DTYPE 0
#define D7905_SECT 48
#define D7905_SURF 3
#define D7905_RH 2
#define D7905_FH (D7905_SURF - D7905_RH)
#define D7905_CYL 411
#define D7905_ID (2 << DS2_V_ID)
#define D7905_SIZE (D7905_SECT * D7905_SURF * D7905_CYL * DS_NUMWD)
#define D7906_DTYPE 1
#define D7906_SECT 48
#define D7906_SURF 4
#define D7906_RH 2
#define D7906_FH (D7906_SURF - D7906_RH)
#define D7906_CYL 411
#define D7906_ID (0 << DS2_V_ID)
#define D7906_SIZE (D7906_SECT * D7906_SURF * D7906_CYL * DS_NUMWD)
#define D7920_DTYPE 2
#define D7920_SECT 48
#define D7920_SURF 5
#define D7920_RH D7920_SURF
#define D7920_FH (D7920_SURF - D7920_RH)
#define D7920_CYL 823
#define D7920_ID (1 << DS2_V_ID)
#define D7920_SIZE (D7920_SECT * D7920_SURF * D7920_CYL * DS_NUMWD)
#define D7925_DTYPE 3
#define D7925_SECT 64
#define D7925_SURF 9
#define D7925_RH D7925_SURF
#define D7925_FH (D7925_SURF - D7925_RH)
#define D7925_CYL 823
#define D7925_ID (3 << DS2_V_ID)
#define D7925_SIZE (D7925_SECT * D7925_SURF * D7925_CYL * DS_NUMWD)
struct drvtyp {
uint32 sc; /* sectors */
uint32 hd; /* surfaces */
uint32 cyl; /* cylinders */
uint32 size; /* #blocks */
uint32 id; /* device type */
uint32 rh; /* removable surfaces */
uint32 fh; /* fixed surfaces */
};
static struct drvtyp drv_tab[] = {
{ D7905_SECT, D7905_SURF, D7905_CYL, D7905_SIZE, D7905_ID, D7905_RH, D7905_FH },
{ D7906_SECT, D7906_SURF, D7906_CYL, D7906_SIZE, D7906_ID, D7906_RH, D7906_FH },
{ D7920_SECT, D7920_SURF, D7920_CYL, D7920_SIZE, D7920_ID, D7920_RH, D7920_FH },
{ D7925_SECT, D7925_SURF, D7925_CYL, D7925_SIZE, D7925_ID, D7925_RH, D7925_FH },
{ 0 }
};
extern uint32 PC, SR;
extern uint32 dev_cmd[2], dev_ctl[2], dev_flg[2], dev_fbf[2], dev_srq[2];
extern int32 sim_switches;
extern UNIT cpu_unit;
uint32 ds_fifo[DS_FIFO_SIZE] = { 0 }; /* fifo */
uint32 ds_fifo_ip = 0; /* insertion ptr */
uint32 ds_fifo_rp = 0; /* removal ptr */
uint32 ds_fifo_cnt = 0; /* count */
uint32 ds_cmd = 0; /* command word */
uint32 ds_sr1 = 0; /* status word 1 */
uint32 ds_busy = 0; /* busy flag */
uint32 ds_eoc = 0; /* end of cylinder */
uint32 ds_eod = 0; /* end of data */
uint32 ds_fmask = 0; /* file mask */
uint32 ds_cmdf = 0; /* command follows */
uint32 ds_cmdp = 0; /* command present */
uint32 ds_cyl = 0; /* disk address: cyl */
uint32 ds_hs = 0; /* disk address: hs */
uint32 ds_vctr = 0; /* verify counter */
uint32 ds_state = 0; /* controller state */
uint32 ds_lastatn = 0; /* last atn intr */
int32 ds_stime = 100; /* seek time */
int32 ds_rtime = 100; /* inter-sector time */
int32 ds_ctime = 3; /* command time */
int32 ds_dtime = 1; /* dch time */
int32 ds_tmo = 2749200; /* timeout = 1.74 sec */
uint32 ds_ptr = 0; /* buffer ptr */
uint16 dsxb[DS_NUMWDF]; /* sector buffer */
static const uint32 ds_opflags[32] = { /* flags for ops */
CMF_CLREC|CMF_CLRS|CMF_UIDLE, /* cold read */
CMF_CLREC|CMF_CLRS|CMF_UIDLE, /* recalibrate */
CMF_CLREC|CMF_CLRS|CMF_UIDLE, /* seek */
0, /* read status */
CMF_CLRS, /* read sector */
CMF_CLRS|CMF_UIDLE, /* read */
CMF_CLRS|CMF_UIDLE, /* read full */
CMF_CLRS|CMF_UIDLE, /* verify */
CMF_CLRS|CMF_UIDLE, /* write */
CMF_CLRS|CMF_UIDLE, /* write full */
CMF_CLRS, /* clear */
CMF_CLRS|CMF_UIDLE, /* init */
CMF_CLREC|CMF_CLRS, /* addr record */
0, /* read syndrome */
CMF_CLRS|CMF_UIDLE, /* read offset */
CMF_CLRS, /* set file mask */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_CLRS|CMF_UIDLE, /* read no verify */
CMF_CLRS, /* write TIO */
CMF_CLRS, /* read disk addr */
CMF_CLRS, /* end */
CMF_CLRS, /* wake */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS, /* undefined */
CMF_UNDF|CMF_CLRS /* undefined */
};
DEVICE ds_dev;
int32 dsio (int32 inst, int32 IR, int32 dat);
t_stat ds_svc_c (UNIT *uptr);
t_stat ds_svc_u (UNIT *uptr);
t_stat ds_svc_t (UNIT *uptr);
t_stat ds_reset (DEVICE *dptr);
t_stat ds_attach (UNIT *uptr, char *cptr);
t_stat ds_detach (UNIT *uptr);
t_stat ds_boot (int32 unitno, DEVICE *dptr);
t_stat ds_load_unload (UNIT *uptr, int32 value, char *cptr, void *desc);
t_stat ds_set_size (UNIT *uptr, int32 val, char *cptr, void *desc);
void ds_poll (void);
void ds_docmd (uint32 cmd);
void ds_doatn (void);
uint32 ds_updds2 (UNIT *uptr);
void ds_cmd_done (t_bool sf, uint32 sr1);
void ds_wait_for_cpu (UNIT *uptr, uint32 newst);
void ds_set_idle (void);
void ds_sched_ctrl_op (uint32 op, uint32 arg, uint32 busy);
void ds_reqad (uint16 *cyl, uint16 *hs);
void ds_start_seek (UNIT *uptr, uint32 cyl, uint32 newst);
t_bool ds_start_rw (UNIT *uptr, int32 tm, t_bool vfy);
void ds_next_sec (UNIT *uptr);
void ds_next_cyl (UNIT *uptr);
t_stat ds_start_rd (UNIT *uptr, uint32 off, t_bool vfy);
void ds_start_wr (UNIT *uptr, t_bool vfy);
void ds_cont_rd (UNIT *uptr, uint32 bsize);
t_stat ds_cont_wr (UNIT *uptr, uint32 off, uint32 bsize);
void ds_end_rw (UNIT *uptr, uint32 newst);
t_stat ds_set_uncorr (UNIT *uptr);
t_stat ds_reset_cmn (DEVICE *dptr);
void ds_sched_atn (UNIT *uptr);
uint32 ds_fifo_read (void);
void ds_fifo_write (uint32 dat);
void ds_fifo_reset (void);
/* DS data structures
ds_dev DS device descriptor
ds_unit DS unit list
ds_reg DS register list
ds_mod DS modifier list
*/
DIB ds_dib = { DS, 0, 0, 0, 0, 0, &dsio };
UNIT ds_unit[] = {
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_u, UNIT_FIX | UNIT_ATTABLE | UNIT_ROABLE |
UNIT_DISABLE | UNIT_UNLOAD, D7905_SIZE) },
{ UDATA (&ds_svc_c, UNIT_DIS, 0) },
{ UDATA (&ds_svc_t, UNIT_DIS, 0) }
};
REG ds_reg[] = {
{ ORDATA (CMD, ds_cmd, 16) },
{ BRDATA (FIFO, ds_fifo, 8, 16, DS_FIFO_SIZE) },
{ ORDATA (SR1, ds_sr1, 16) },
{ ORDATA (VCTR, ds_vctr, 16) },
{ ORDATA (FMASK, ds_fmask, 8) },
{ ORDATA (CYL, ds_cyl, 16) },
{ ORDATA (HS, ds_hs, 16) },
{ ORDATA (STATE, ds_state, 2), REG_RO },
{ ORDATA (LASTA, ds_lastatn, 3) },
{ DRDATA (FIP, ds_fifo_ip, 4) },
{ DRDATA (FRP, ds_fifo_rp, 4) },
{ DRDATA (FCNT, ds_fifo_cnt, 5) },
{ FLDATA (CMD, ds_dib.cmd, 0), REG_HRO },
{ FLDATA (CTL, ds_dib.ctl, 0) },
{ FLDATA (FLG, ds_dib.flg, 0) },
{ FLDATA (FBF, ds_dib.fbf, 0) },
{ FLDATA (SRQ, ds_dib.srq, 0) },
{ FLDATA (BUSY, ds_busy, 0) },
{ FLDATA (CMDF, ds_cmdf, 0) },
{ FLDATA (CMDP, ds_cmdp, 0) },
{ FLDATA (EOC, ds_eoc, 0) },
{ FLDATA (EOD, ds_eod, 0) },
{ BRDATA (DBUF, dsxb, 8, 16, DS_NUMWDF) },
{ FLDATA (DPTR, ds_ptr, 8) },
{ DRDATA (CTIME, ds_ctime, 24), PV_LEFT + REG_NZ },
{ DRDATA (DTIME, ds_dtime, 24), PV_LEFT + REG_NZ },
{ DRDATA (STIME, ds_stime, 24), PV_LEFT + REG_NZ },
{ DRDATA (RTIME, ds_rtime, 24), PV_LEFT + REG_NZ },
{ DRDATA (TIMEOUT, ds_tmo, 31), PV_LEFT + REG_NZ },
{ URDATA (UCYL, ds_unit[0].CYL, 10, 10, 0,
DS_NUMDR + 1, PV_LEFT | REG_HRO) },
{ URDATA (UFNC, ds_unit[0].FNC, 8, 8, 0,
DS_NUMDR + 1, REG_HRO) },
{ URDATA (USTA, ds_unit[0].STA, 8, 16, 0,
DS_NUMDR + 1, REG_HRO) },
{ URDATA (CAPAC, ds_unit[0].capac, 10, T_ADDR_W, 0,
DS_NUMDR, PV_LEFT | REG_HRO) },
{ ORDATA (DEVNO, ds_dib.devno, 6), REG_HRO },
{ NULL }
};
MTAB ds_mod[] = {
{ UNIT_UNLOAD, UNIT_UNLOAD, "heads unloaded", "UNLOADED", ds_load_unload },
{ UNIT_UNLOAD, 0, "heads loaded", "LOADED", ds_load_unload },
{ UNIT_WLK, 0, "write enabled", "WRITEENABLED", NULL },
{ UNIT_WLK, UNIT_WLK, "write locked", "LOCKED", NULL },
{ UNIT_FMT, 0, "format disabled", "NOFORMAT", NULL },
{ UNIT_FMT, UNIT_FMT, "format enabled", "FORMAT", NULL },
{ (UNIT_DTYPE+UNIT_ATT), (D7905_DTYPE << UNIT_V_DTYPE) + UNIT_ATT,
"7905", NULL, NULL },
{ (UNIT_DTYPE+UNIT_ATT), (D7906_DTYPE << UNIT_V_DTYPE) + UNIT_ATT,
"7906", NULL, NULL },
{ (UNIT_DTYPE+UNIT_ATT), (D7920_DTYPE << UNIT_V_DTYPE) + UNIT_ATT,
"7920", NULL, NULL },
{ (UNIT_DTYPE+UNIT_ATT), (D7925_DTYPE << UNIT_V_DTYPE) + UNIT_ATT,
"7925", NULL, NULL },
{ (UNIT_AUTO+UNIT_DTYPE+UNIT_ATT), (D7905_DTYPE << UNIT_V_DTYPE),
"7905", NULL, NULL },
{ (UNIT_AUTO+UNIT_DTYPE+UNIT_ATT), (D7906_DTYPE << UNIT_V_DTYPE),
"7906", NULL, NULL },
{ (UNIT_AUTO+UNIT_DTYPE+UNIT_ATT), (D7920_DTYPE << UNIT_V_DTYPE),
"7920", NULL, NULL },
{ (UNIT_AUTO+UNIT_DTYPE+UNIT_ATT), (D7925_DTYPE << UNIT_V_DTYPE),
"7925", NULL, NULL },
{ (UNIT_AUTO+UNIT_ATT), UNIT_AUTO, "autosize", NULL, NULL },
{ UNIT_AUTO, UNIT_AUTO, NULL, "AUTOSIZE", NULL },
{ (UNIT_AUTO+UNIT_DTYPE), (D7905_DTYPE << UNIT_V_DTYPE),
NULL, "7905", &ds_set_size },
{ (UNIT_AUTO+UNIT_DTYPE), (D7906_DTYPE << UNIT_V_DTYPE),
NULL, "7906", &ds_set_size },
{ (UNIT_AUTO+UNIT_DTYPE), (D7920_DTYPE << UNIT_V_DTYPE),
NULL, "7920", &ds_set_size },
{ (UNIT_AUTO+UNIT_DTYPE), (D7925_DTYPE << UNIT_V_DTYPE),
NULL, "7925", &ds_set_size },
{ MTAB_XTD | MTAB_VDV, 0, "DEVNO", "DEVNO",
&hp_setdev, &hp_showdev, &ds_dev },
{ 0 }
};
DEVICE ds_dev = {
"DS", ds_unit, ds_reg, ds_mod,
DS_NUMDR + 2, 8, 27, 1, 8, 16,
NULL, NULL, &ds_reset,
&ds_boot, &ds_attach, &ds_detach,
&ds_dib, DEV_DISABLE
};
/* IO instructions */
int32 dsio (int32 inst, int32 IR, int32 dat)
{
uint32 dev = IR & I_DEVMASK;
switch (inst) { /* case on opcode */
case ioFLG: /* flag clear/set */
if ((IR & I_HC) == 0) { setFLG (dev); } /* STF */
break;
case ioSFS: /* skip flag set */
if (FLG (dev) != 0) PC = (PC + 1) & VAMASK;
break;
case ioSFC: /* skip flag clear */
if (ds_busy == 0) PC = (PC + 1) & VAMASK;
break;
case ioOTX: /* output */
if (ds_cmdf) { /* expecting command? */
ds_cmd = dat; /* save command */
ds_cmdf = 0;
ds_cmdp = 1; /* command present */
}
else ds_fifo_write (dat); /* put in fifo */
break;
case ioMIX: /* merge */
dat = dat | ds_fifo_read ();
break;
case ioLIX: /* load */
dat = ds_fifo_read ();
break;
case ioCTL: /* control clear/set */
if (IR & I_CTL) { /* CLC */
clrCTL (dev); /* clear control */
ds_cmdf = 1; /* expecting command */
ds_cmdp = 0; /* none pending */
ds_fifo_reset (); /* clear fifo */
}
else { /* STC */
setCTL (dev); /* set ctl */
}
break;
case ioEDT: /* end of transfer */
ds_eod = 1; /* flag end transfer */
break;
default:
break;
}
if (IR & I_HC) { clrFSR (dev); } /* H/C option */
ds_poll (); /* run the controller */
return dat;
}
/* Run the controller polling loop, based on ds_state:
IDLE commands and ATN interrupts
WAIT commands only
BUSY nothing
*/
void ds_poll (void)
{
int32 dev = ds_dib.devno;
if ((ds_state != DS_BUSY) && ds_cmdp) ds_docmd (ds_cmd);/* cmd pending? */
if ((ds_state == DS_IDLE) && CTL (dev)) ds_doatn (); /* idle? check ATN */
return;
}
/* Process a command - ctrl state is either IDLE or WAIT.
- A drive may be processing a seek or recalibrate
- The controller unit is idle
- If the command can be processed, ds_state is set to BUSY, and
the interface command buffer is cleared
- If the command cannot be processed, ds_state is set to WAIT,
and the command is retained in the interface command buffer */
void ds_docmd (uint32 cmd)
{
uint32 op, f, dtyp, unum;
op = DSC_GETOP (cmd); /* operation */
f = ds_opflags[op]; /* flags */
if (op == DSC_COLD) unum = 0; /* boot force unit 0 */
else unum = DSC_GETUNIT (cmd); /* get unit */
if ((f & CMF_UIDLE) && (unum < DS_NUMDR) && /* idle required */
sim_is_active (&ds_unit[unum])) { /* but unit busy? */
ds_state = DS_WAIT; /* wait */
return;
}
ds_cmdp = 0; /* flush command */
ds_state = DS_BUSY; /* ctrl is busy */
if (f & CMF_CLRS) ds_sr1 = 0; /* clear status */
if (f & CMF_CLREC) ds_eoc = 0; /* clear end cyl */
if (f & CMF_UNDF) { /* illegal op? */
ds_sched_ctrl_op (DSC_BADF, 0, CLR_BUSY); /* sched, clr busy */
return;
}
switch (op) {
/* Drive commands */
case DSC_COLD: /* cold load read */
ds_fmask = DSC_SPEN; /* sparing enabled */
ds_cyl = 0; /* cylinder 0 */
ds_hs = (DSC_GETCHD (ds_cmd) << DSHS_V_HD) | /* reformat hd/sec */
(DSC_GETCSC (ds_cmd) << DSHS_V_SC);
case DSC_RECAL: /* recalibrate */
case DSC_SEEK: /* seek */
case DSC_READ: /* read */
case DSC_RFULL: /* read full */
case DSC_ROFF: /* read offset */
case DSC_RNOVFY: /* read no verify */
case DSC_VFY: /* verify */
case DSC_WRITE: /* write */
case DSC_WFULL: /* write full */
case DSC_INIT: /* init */
ds_sr1 = unum; /* init status */
if (unum >= DS_NUMDR) { /* invalid unit? */
ds_sched_ctrl_op (DSC_BADU, unum, CLR_BUSY);/* sched, not busy */
return;
}
if (op == DSC_INIT) ds_sr1 |= /* init? */
((cmd & DSC_SPAR)? DS1_SPAR: 0) | /* copy SPD to stat1 */
((cmd & DSC_PROT)? DS1_PROT: 0) |
((cmd & DSC_DFCT)? DS1_DFCT: 0);
ds_unit[unum].FNC = op; /* save op */
ds_unit[unum].STA &= ~DS2_ATN; /* clear ATN */
sim_cancel (&ds_unit[unum]); /* cancel current */
sim_activate (&ds_unit[unum], ds_ctime); /* schedule unit */
ds_busy = 1; /* set visible busy */
break;
/* Read status commands */
case DSC_RSTA: /* read status */
dsxb[1] = ds_sr1; /* return SR1 */
if (unum < DS_NUMDR) { /* and SR2 */
dsxb[0] = ds_updds2 (&ds_unit[unum]);
ds_unit[unum].STA &= ~DS2_FS; /* clear 1st */
}
else dsxb[0] = DS2_ERR|DS2_NR;
ds_sched_ctrl_op (DSC_RSTA, 2, SET_BUSY); /* sched 2 wds, busy */
break;
case DSC_RSA: /* read sector address */
dtyp = GET_DTYPE (ds_unit[unum].flags); /* get unit type */
dsxb[0] = GET_CURSEC (ds_dtime * DS_NUMWD, dtyp); /* rot position */
ds_sched_ctrl_op (DSC_RSTA, 1, SET_BUSY); /* sched 1 wd, busy */
break;
case DSC_RDA: /* read disk address */
ds_reqad (&dsxb[1], &dsxb[0]); /* return disk address */
ds_sched_ctrl_op (DSC_RSTA, 2, SET_BUSY); /* sched 2 wds, busy */
break;
case DSC_RSYN: /* read syndrome */
dsxb[6] = ds_sr1; /* return SR1 */
ds_reqad (&dsxb[5], &dsxb[4]); /* return disk address */
dsxb[3] = dsxb[2] = dsxb[1] = dsxb[0] = 0; /* syndrome is 0 */
ds_sched_ctrl_op (DSC_RSTA, 7, SET_BUSY); /* sched 7 wds, busy */
break;
/* Other controller commands */
case DSC_SFM: /* set file mask */
case DSC_CLEAR: /* clear */
case DSC_AREC: /* address record */
case DSC_WAKE: /* wakeup */
case DSC_WTIO: /* write TIO */
ds_sched_ctrl_op (op, 0, SET_BUSY); /* schedule, busy */
break;
case DSC_END: /* end */
ds_set_idle (); /* idle ctrl */
break;
}
return;
}
/* Check for attention */
void ds_doatn (void)
{
uint32 i, dev;
dev = ds_dib.devno; /* device num */
for (i = 0; i < DS_NUMDR; i++) { /* intr disabled? */
ds_lastatn = (ds_lastatn + 1) & DS_DRMASK; /* loop through units */
if (ds_unit[ds_lastatn].STA & DS2_ATN) { /* ATN set? */
ds_unit[ds_lastatn].STA &= ~DS2_ATN; /* clear ATN */
setFLG (dev); /* request interrupt */
ds_sr1 = DS1_ATN | ds_lastatn; /* set up status 1 */
ds_state = DS_WAIT; /* block atn intrs */
return;
}
}
return;
}
/* Controller service
The argument for the function, if any, is stored in uptr->CYL */
t_stat ds_svc_c (UNIT *uptr)
{
uint32 op, dev;
op = uptr->FNC;
dev = ds_dib.devno;
switch (op) {
case DSC_AREC: /* address record */
ds_wait_for_cpu (uptr, DSC_AREC|DSC_2ND); /* set flag, new state */
break;
case DSC_AREC | DSC_2ND: /* poll done */
if (!DS_FIFO_EMPTY) { /* OTA ds? */
ds_cyl = ds_fifo_read (); /* save cylinder */
ds_wait_for_cpu (uptr, DSC_AREC|DSC_3RD); /* set flag, new state */
}
else sim_activate (uptr, ds_ctime); /* no, continue poll */
break;
case DSC_AREC | DSC_3RD: /* poll done */
if (!DS_FIFO_EMPTY) { /* OTA ds? */
ds_hs = ds_fifo_read (); /* save head/sector */
ds_cmd_done (0, DS1_OK); /* op done, no flag */
}
else sim_activate (uptr, ds_ctime); /* no, continue poll */
break;
case DSC_RSTA: /* rd stat (all forms) */
if (DS_FIFO_EMPTY) { /* fifo empty? */
uptr->CYL--;
ds_fifo_write (dsxb[uptr->CYL]); /* store next status */
ds_wait_for_cpu (uptr, DSC_RSTA |
(uptr->CYL? 0: DSC_2ND)); /* set flag, new state */
}
else sim_activate (uptr, ds_ctime); /* no, continue poll */
break;
case DSC_RSTA | DSC_2ND: /* poll done */
if (DS_FIFO_EMPTY) ds_cmd_done (0, DS1_OK); /* op done? no flag */
else sim_activate (uptr, ds_ctime); /* no, continue poll */
break;
case DSC_CLEAR: /* clear */
ds_reset_cmn (&ds_dev); /* reset ctrl */
clrCTL (dev); /* clear CTL, SRQ */
clrSRQ (dev);
ds_cmd_done (1, DS1_OK); /* op done, set flag */
break;
case DSC_SFM: /* set file mask */
ds_fmask = ds_cmd & DSC_FMASK;
ds_cmd_done (1, DS1_OK); /* op done, set flag */
break;
case DSC_WTIO: /* write I/O */
ds_cmd_done (0, DS1_OK); /* op done, no flag */
break;
case DSC_WAKE: /* wakeup */
ds_cmd_done (1, DS1_AVAIL); /* op done, set flag */
break;
case DSC_BADU: /* invalid unit */
if (uptr->CYL > 10) ds_cmd_done (1, DS1_UNAVL); /* [11,16]? bad unit */
else ds_cmd_done (1, DS1_S2ERR); /* else unit not ready */
break;
case DSC_BADF: /* invalid operation */
ds_cmd_done (1, DS1_ILLOP); /* op done, set flag */
break;
default:
return SCPE_IERR;
}
ds_poll (); /* run the controller */
return SCPE_OK;
}
/* Timeout service */
t_stat ds_svc_t (UNIT *uptr)
{
int32 i;
for (i = 0; i < (DS_NUMDR + 1); i++) /* cancel all ops */
sim_cancel (&ds_unit[i]);
ds_set_idle (); /* idle the controller */
ds_fmask = 0; /* clear file mask */
ds_poll (); /* run the controller */
return SCPE_OK;
}
/* Unit service */
t_stat ds_svc_u (UNIT *uptr)
{
uint32 op, dev, dtyp;
t_stat r;
op = uptr->FNC;
dev = ds_dib.devno;
dtyp = GET_DTYPE (uptr->flags);
switch (op) { /* case on function */
/* Seek and recalibrate */
case DSC_RECAL: /* recalibrate */
if ((uptr->flags & UNIT_UNLOAD) == 0) { /* drive up? */
ds_start_seek (uptr, 0, DSC_RECAL|DSC_2ND); /* set up seek */
ds_set_idle (); /* ctrl is idle */
}
else ds_cmd_done (1, DS1_S2ERR); /* not ready error */
break;
case DSC_RECAL | DSC_2ND: /* recal complete */
uptr->STA = uptr->STA | DS2_ATN; /* set attention */
break;
case DSC_SEEK: /* seek */
ds_wait_for_cpu (uptr, DSC_SEEK|DSC_2ND); /* set flag, new state */
break;
case DSC_SEEK | DSC_2ND: /* waiting for word 1 */
if (!DS_FIFO_EMPTY) { /* OTA ds? */
ds_cyl = ds_fifo_read (); /* save cylinder */
ds_wait_for_cpu (uptr, DSC_SEEK|DSC_3RD); /* set flag, new state */
}
else sim_activate (uptr, ds_ctime); /* no, continue poll */
break;
case DSC_SEEK | DSC_3RD: /* waiting for word 2 */
if (!DS_FIFO_EMPTY) { /* OTA ds? */
ds_hs = ds_fifo_read (); /* save head/sector */
if ((uptr->flags & UNIT_UNLOAD) == 0) { /* drive up? */
ds_start_seek (uptr, ds_cyl, DSC_SEEK|DSC_4TH); /* set up seek */
ds_set_idle (); /* ctrl is idle */
}
else ds_cmd_done (1, DS1_S2ERR); /* else not ready error */
}
else sim_activate (uptr, ds_ctime); /* continue poll */
break;
case DSC_SEEK | DSC_4TH: /* seek complete */
uptr->STA = uptr->STA | DS2_ATN; /* set attention */
break;
/* Read variants */
case DSC_ROFF: /* read with offset */
ds_wait_for_cpu (uptr, DSC_ROFF|DSC_2ND); /* set flag, new state */
break;
case DSC_ROFF | DSC_2ND: /* poll done */
if (!DS_FIFO_EMPTY) { /* OTA ds? new state */
ds_fifo_read (); /* drain fifo */
uptr->FNC = DSC_READ;
setFLG (dev); /* handshake */
}
sim_activate (uptr, ds_ctime); /* schedule unit */
break;
case DSC_COLD: /* cold load read */
if ((uptr->flags & UNIT_UNLOAD) == 0) /* drive up? */
ds_start_seek (uptr, 0, DSC_READ); /* set up seek */
else ds_cmd_done (1, DS1_S2ERR); /* no, not ready error */
break;
case DSC_READ: /* read */
if (r = ds_start_rd (uptr, 0, 1)) return r; /* new sector; error? */
break;
case DSC_READ | DSC_2ND: /* word transfer */
ds_cont_rd (uptr, DS_NUMWD); /* xfr wd, check end */
break;
case DSC_READ | DSC_3RD: /* end of sector */
ds_end_rw (uptr, DSC_READ); /* see if more to do */
break;
case DSC_RNOVFY: /* read, no verify */
if (r = ds_start_rd (uptr, 0, 0)) return r; /* new sector; error? */
break;
case DSC_RNOVFY | DSC_2ND: /* word transfer */
ds_cont_rd (uptr, DS_NUMWD); /* xfr wd, check end */
break;
case DSC_RNOVFY | DSC_3RD: /* end of sector */
ds_end_rw (uptr, DSC_RNOVFY); /* see if more to do */
break;
case DSC_RFULL: /* read full */
dsxb[DS_FSYNC] = 0100376; /* fill in header */
dsxb[DS_FCYL] = uptr->CYL;
dsxb[DS_FHS] = ds_hs; /* before h/s update */
if (r = ds_start_rd (uptr, DS_FDATA, 0)) /* new sector; error? */
return r;
break;
case DSC_RFULL | DSC_2ND: /* word transfer */
ds_cont_rd (uptr, DS_NUMWDF); /* xfr wd, check end */
break;
case DSC_RFULL | DSC_3RD: /* end of sector */
ds_end_rw (uptr, DSC_RFULL); /* see if more to do */
break;
case DSC_VFY: /* verify */
ds_wait_for_cpu (uptr, DSC_VFY|DSC_2ND); /* set flag, new state */
break;
case DSC_VFY | DSC_2ND: /* poll done */
if (!DS_FIFO_EMPTY) { /* OTA ds? */
ds_vctr = ds_fifo_read (); /* save count */
uptr->FNC = DSC_VFY | DSC_3RD; /* next state */
sim_activate (uptr, ds_rtime); /* delay for transfer */
}
else sim_activate (uptr, ds_ctime); /* no, continue poll */
break;
case DSC_VFY | DSC_3RD: /* start sector */
if (ds_start_rw (uptr, ds_dtime * DS_NUMWD, 1)) break;
/* new sector; error? */
ds_next_sec (uptr); /* increment hd, sc */
break;
case DSC_VFY | DSC_4TH: /* end sector */
ds_vctr = (ds_vctr - 1) & DMASK; /* decrement count */
if (ds_vctr) ds_end_rw (uptr, DSC_VFY|DSC_3RD); /* more to do? */
else ds_cmd_done (1, DS1_OK); /* no, set done */
break;
/* Write variants */
case DSC_WRITE: /* write */
ds_start_wr (uptr, 1); /* new sector */
break;
case DSC_WRITE | DSC_2ND:
if (r = ds_cont_wr (uptr, 0, DS_NUMWD)) /* write word */
return r; /* error? */
break;
case DSC_WRITE | DSC_3RD: /* end sector */
ds_end_rw (uptr, DSC_WRITE); /* see if more to do */
break;
case DSC_INIT: /* init */
ds_start_wr (uptr, 0); /* new sector */
break;
case DSC_INIT | DSC_2ND:
if (r = ds_cont_wr (uptr, 0, DS_NUMWD)) /* write word */
return r; /* error? */
break;
case DSC_INIT | DSC_3RD: /* end sector */
ds_end_rw (uptr, DSC_INIT); /* see if more to do */
break;
case DSC_WFULL: /* write full */
ds_start_wr (uptr, 0); /* new sector */
break;
case DSC_WFULL | DSC_2ND:
if (r = ds_cont_wr (uptr, DS_FDATA, DS_NUMWDF)) /* write word */
return r; /* error */
break;
case DSC_WFULL | DSC_3RD:
ds_end_rw (uptr, DSC_WFULL); /* see if more to do */
break;
default:
break;
}
ds_poll ();
return SCPE_OK;
}
/* Schedule timed wait for CPU response
- Set flag to get CPU attention
- Set specified unit to 'newstate' and schedule
- Schedule timeout */
void ds_wait_for_cpu (UNIT *uptr, uint32 newst)
{
uint32 dev = ds_dib.devno;
setFLG (dev); /* set flag */
uptr->FNC = newst; /* new state */
sim_activate (uptr, ds_ctime); /* activate unit */
sim_cancel (&ds_timer); /* activate timeout */
sim_activate (&ds_timer, ds_tmo);
return;
}
/* Set idle state
- Controller is set to idle state
- Visible busy is cleared
- Timeout is cancelled */
void ds_set_idle (void)
{
ds_busy = 0; /* busy clear */
ds_state = DS_IDLE; /* ctrl idle */
sim_cancel (&ds_timer); /* no timeout */
return;
}
/* Set wait state
- Set flag if required
- Set controller to wait state
- Clear visible busy
- Schedule timeout */
void ds_cmd_done (t_bool sf, uint32 sr1)
{
uint32 dev = ds_dib.devno;
if (sf) { setFLG (dev); } /* set host flag */
ds_busy = 0; /* clear visible busy */
ds_sr1 = ds_sr1 | sr1; /* final status */
ds_state = DS_WAIT; /* ctrl waiting */
sim_cancel (&ds_timer); /* activate timeout */
sim_activate (&ds_timer, ds_tmo);
return;
}
/* Return drive status (status word 2) */
uint32 ds_updds2 (UNIT *uptr)
{
uint32 sta;
uint32 dtyp = GET_DTYPE (uptr->flags);
sta = drv_tab[dtyp].id | /* form status */
uptr->STA | /* static bits */
((uptr->flags & UNIT_WPR)? DS2_RO: 0) | /* dynamic bits */
((uptr->flags & UNIT_FMT)? DS2_FRM: 0) |
((uptr->flags & UNIT_UNLOAD)? DS2_NR | DS2_BS: 0) |
(sim_is_active (uptr)? DS2_BS: 0);
if (sta & DS2_ALLERR) sta = sta | DS2_ERR; /* set error */
return sta;
}
/* Schedule controller operation */
void ds_sched_ctrl_op (uint32 op, uint32 arg, uint32 busy)
{
ds_ctrl.FNC = op; /* save op */
ds_ctrl.CYL = arg; /* save argument */
ds_busy = busy; /* set visible busy */
sim_activate (&ds_ctrl, ds_ctime); /* schedule */
sim_cancel (&ds_timer); /* activate timeout */
sim_activate (&ds_timer, ds_tmo);
return;
}
/* Request address - if pending eoc, report cylinder + 1 */
void ds_reqad (uint16 *cyl, uint16 *hs)
{
*cyl = ds_cyl + (ds_eoc? 1: 0);
*hs = ds_hs;
return;
}
/* Start seek - schedule whether in bounds or out of bounds */
void ds_start_seek (UNIT *uptr, uint32 cyl, uint32 newst)
{
int32 t;
uint32 hd, sc;
uint32 dtyp = GET_DTYPE (uptr->flags);
uptr->FNC = newst; /* set new state */
if (cyl >= drv_tab[dtyp].cyl) { /* out of bounds? */
t = 0; /* don't change cyl */
uptr->STA = uptr->STA | DS2_SC; /* set seek check */
}
else {
t = abs (uptr->CYL - cyl); /* delta cylinders */
uptr->CYL = cyl; /* put on cylinder */
hd = DSHS_GETHD (ds_hs); /* invalid head or sec? */
sc = DSHS_GETSC (ds_hs);
if ((hd >= drv_tab[dtyp].hd) ||
(sc >= drv_tab[dtyp].sc))
uptr->STA = uptr->STA | DS2_SC; /* set seek check */
else uptr->STA = uptr->STA & ~DS2_SC; /* clear seek check */
}
sim_activate (uptr, ds_stime * (t + 1)); /* schedule */
return;
}
/* Start next sector for read or write
- If error, set command done, return TRUE, nothing is scheduled
- If implicit seek, return TRUE, implicit seek is scheduled, but
state is not changed - we will return here when seek is done
- Otherwise, advance state, set position in file, schedule next state */
t_bool ds_start_rw (UNIT *uptr, int32 tm, t_bool vfy)
{
uint32 da, hd, sc;
uint32 dtyp = GET_DTYPE (uptr->flags);
ds_eod = 0; /* init eod */
ds_ptr = 0; /* init buffer ptr */
if (uptr->flags & UNIT_UNLOAD) { /* drive down? */
ds_cmd_done (1, DS1_S2ERR);
return TRUE;
}
if (ds_eoc) { /* at end of cylinder? */
ds_next_cyl (uptr); /* auto seek to next */
return TRUE; /* or error */
}
if (vfy && ((uint32) uptr->CYL != ds_cyl)) { /* on wrong cylinder? */
if (ds_cyl >= drv_tab[dtyp].cyl) /* seeking to bad? */
ds_cmd_done (1, DS1_CYLCE); /* lose */
else ds_start_seek (uptr, ds_cyl, uptr->FNC); /* seek right cyl */
return TRUE;
}
hd = DSHS_GETHD (ds_hs);
sc = DSHS_GETSC (ds_hs);
if ((uint32) uptr->CYL >= drv_tab[dtyp].cyl) { /* valid cylinder? */
uptr->STA = uptr->STA | DS2_SC; /* set seek check */
ds_cmd_done (1, DS1_S2ERR); /* error */
return TRUE;
}
if ((hd >= drv_tab[dtyp].hd) || /* valid head, sector? */
(sc >= drv_tab[dtyp].sc)) {
ds_cmd_done (1, DS1_HSCE); /* no, error */
return TRUE;
}
da = GET_DA (uptr->CYL, hd, sc, dtyp); /* position in file */
sim_fseek (uptr->fileref, da * sizeof (uint16), SEEK_SET); /* set file pos */
uptr->FNC += DSC_NEXT; /* next state */
sim_activate (uptr, tm); /* activate unit */
return FALSE;
}
/* Start next sector for read
- Do common start for read and write
- If error, return, command has been terminated, nothing scheduled
- If implicit seek, return, seek scheduled
- If no error or seek, state has been advanced and unit scheduled
- Read sector
- If read error, terminate command and return, nothing scheduled
- If no error, advance head/sector, next state scheduled */
t_stat ds_start_rd (UNIT *uptr, uint32 off, t_bool vfy)
{
uint32 t;
if (ds_start_rw (uptr, ds_rtime, vfy)) return SCPE_OK; /* new sec; err or seek? */
t = sim_fread (dsxb + off, sizeof (uint16), DS_NUMWD, uptr->fileref);
for (t = t + off ; t < DS_NUMWDF; t++) dsxb[t] = 0; /* fill sector */
if (ferror (uptr->fileref)) /* error? */
return ds_set_uncorr (uptr); /* say uncorrectable */
ds_next_sec (uptr); /* increment hd, sc */
return SCPE_OK;
}
/* Start next sector for write
- Do common start for read and write
- If error, return, command has been terminated, nothing scheduled
- If implicit seek, return, seek scheduled
- If no error or seek, state has been advanced and unit scheduled
- Clear buffer
- Set service request */
void ds_start_wr (UNIT *uptr, t_bool vfy)
{
uint32 i;
uint32 dev = ds_dib.devno;
if ((uptr->flags & UNIT_WPR) || /* write protected? */
(!vfy && ((uptr->flags & UNIT_FMT) == 0))) { /* format, not enbl? */
ds_cmd_done (1, DS1_S2ERR); /* error */
return;
}
if (ds_start_rw (uptr, ds_rtime, vfy)) return; /* new sec; err or seek? */
for (i = 0; i < DS_NUMWDF; i++) dsxb[i] = 0; /* clear buffer */
setSRQ (dev); /* request word */
return;
}
/* Advance to next sector (but not next cylinder) */
void ds_next_sec (UNIT *uptr)
{
uint32 dtyp = GET_DTYPE (uptr->flags);
ds_hs = ds_hs + 1; /* increment sector */
if (DSHS_GETSC (ds_hs) < drv_tab[dtyp].sc) return; /* end of track? */
ds_hs = ds_hs & ~DSHS_SC; /* yes, wrap sector */
if (ds_fmask & DSC_CYLM) { /* cylinder mode? */
ds_hs = ds_hs + (1 << DSHS_V_HD); /* increment head */
if (DSHS_GETHD (ds_hs) < drv_tab[dtyp].hd) return; /* end of cyl? */
ds_hs = ds_hs & ~DSHS_HD; /* 0 head */
}
ds_eoc = 1; /* flag end cylinder */
return;
}
/* Advance to next cylinder
- If autoseek enabled, seek to cylinder +/- 1
- Otherwise, done with end of cylinder error */
void ds_next_cyl (UNIT *uptr)
{
if (ds_fmask & DSC_AUTO) { /* auto seek allowed? */
if (ds_fmask & DSC_DECR) ds_cyl = (ds_cyl - 1) & DMASK;
else ds_cyl = (ds_cyl + 1) & DMASK;
ds_eoc = 0; /* clear end cylinder */
ds_start_seek (uptr, ds_cyl, uptr->FNC); /* seek, same state */
}
else ds_cmd_done (1, DS1_EOCYL); /* no, end of cyl err */
return;
}
/* Transfer word for read
- If end of data, terminate command, nothing scheduled
- Otherwise, transfer word, advance state if last word, schedule */
void ds_cont_rd (UNIT *uptr, uint32 bsize)
{
uint32 dev = ds_dib.devno;
if (ds_eod) ds_cmd_done (1, DS1_OK); /* DMA end? done */
else if (SRQ (dev)) { /* overrun? */
ds_cmd_done (1, DS1_OVRUN); /* set done */
return;
}
else { ds_fifo_write (dsxb[ds_ptr++]); /* next word */
setSRQ (dev); /* request service */
if (ds_ptr >= bsize) uptr->FNC += DSC_NEXT; /* sec done? next state */
sim_activate (uptr, ds_dtime); /* schedule */
}
return;
}
/* Transfer word for write
- Copy word from fifo to buffer
- If end of data, write buffer, terminate command, nothing scheduled
- If end of sector, write buffer, next state, schedule
- Otherwises, set service request, schedule */
t_stat ds_cont_wr (UNIT *uptr, uint32 off, uint32 bsize)
{
uint32 i, dat;
uint32 dev = ds_dib.devno;
if (SRQ (dev)) { /* overrun? */
ds_cmd_done (1, DS1_OVRUN); /* set done */
return SCPE_OK;
}
dsxb[ds_ptr++] = dat = ds_fifo_read (); /* next word */
if (ds_eod || (ds_ptr >= bsize)) { /* xfr or sector done? */
for (i = ds_ptr; i < bsize; i++) dsxb[i] = dat; /* fill sector */
sim_fwrite (dsxb + off, sizeof (uint16), DS_NUMWD, uptr->fileref);
if (ferror (uptr->fileref)) /* error on write? */
return ds_set_uncorr (uptr); /* uncorrectable */
ds_next_sec (uptr); /* increment hd, sc */
if (ds_eod) { /* end data? */
ds_cmd_done (1, DS1_OK); /* set done */
return SCPE_OK;
}
else uptr->FNC += DSC_NEXT; /* no, next state */
}
else { setSRQ (dev); } /* request next word */
sim_activate (uptr, ds_dtime); /* schedule */
return SCPE_OK;
}
/* End sector for read or write
- If end of data, terminate command, nothing scheduled
- If end of cylinder, schedule next cylinder
- Else schedule start of next sector */
void ds_end_rw (UNIT *uptr, uint32 newst)
{
uptr->FNC = newst; /* new state */
if (ds_eod) ds_cmd_done (1, DS1_OK); /* done? */
else if (ds_eoc) ds_next_cyl (uptr); /* end cyl? seek */
else sim_activate (uptr, ds_rtime); /* normal transfer */
return;
}
/* Report uncorrectable data error */
t_stat ds_set_uncorr (UNIT *uptr)
{
sim_cancel (uptr); /* cancel any operation */
ds_cmd_done (1, DS1_UNCOR); /* done with error */
perror ("DS I/O error"); /* visible error */
clearerr (uptr->fileref);
ds_poll (); /* force poll */
return SCPE_IOERR;
}
/* Fifo read */
uint32 ds_fifo_read (void)
{
uint32 dat;
if (ds_fifo_cnt == 0) return ds_fifo[ds_fifo_rp];
dat = ds_fifo[ds_fifo_rp++];
if (ds_fifo_rp >= DS_FIFO_SIZE) ds_fifo_rp = 0;
ds_fifo_cnt--;
return dat;
}
void ds_fifo_write (uint32 dat)
{
ds_fifo[ds_fifo_ip++] = dat;
if (ds_fifo_ip >= DS_FIFO_SIZE) ds_fifo_ip = 0;
if (ds_fifo_cnt < DS_FIFO_SIZE) ds_fifo_cnt++;
return;
}
void ds_fifo_reset (void)
{
uint32 i;
ds_fifo_ip = ds_fifo_rp = ds_fifo_cnt = 0;
for (i = 0; i < DS_FIFO_SIZE; i++) ds_fifo[i] = 0;
return;
}
/* Reset routine */
t_stat ds_reset_cmn (DEVICE *dptr)
{
int32 i;
ds_cmd = 0; /* clear command */
ds_cmdf = ds_cmdp = 0; /* clear commands flops */
ds_fifo_reset (); /* clear fifo */
ds_eoc = ds_eod = 0;
ds_busy = 0;
ds_state = DS_IDLE; /* ctrl idle */
ds_lastatn = 0;
ds_fmask = 0;
ds_ptr = 0;
ds_cyl = ds_hs = 0;
ds_vctr = 0;
for (i = 0; i < DS_NUMDR; i++) { /* loop thru drives */
sim_cancel (&ds_unit[i]); /* cancel activity */
ds_unit[i].FNC = 0; /* clear function */
ds_unit[i].CYL = 0;
ds_unit[i].STA = 0;
}
sim_cancel (&ds_ctrl);
sim_cancel (&ds_timer);
return SCPE_OK;
}
t_stat ds_reset (DEVICE *dptr)
{
ds_dib.cmd = 0; /* clear cmd */
ds_dib.ctl = 0; /* clear ctl */
ds_dib.fbf = 1; /* set fbf */
ds_dib.flg = 1; /* set flg */
ds_dib.srq = 0; /* clear srq */
return ds_reset_cmn (dptr); /* do common reset */
}
/* Device attach */
t_stat ds_attach (UNIT *uptr, char *cptr)
{
uint32 i, p;
t_stat r;
uptr->capac = drv_tab[GET_DTYPE (uptr->flags)].size;
r = attach_unit (uptr, cptr); /* attach unit */
if (r != SCPE_OK) return r; /* error? */
ds_load_unload (uptr, 0, NULL, NULL); /* if OK, load heads */
ds_sched_atn (uptr); /* schedule attention */
if (((uptr->flags & UNIT_AUTO) == 0) || /* static size? */
((p = sim_fsize (uptr->fileref)) == 0)) return SCPE_OK; /* new file? */
for (i = 0; drv_tab[i].sc != 0; i++) { /* find best fit */
if (p <= (drv_tab[i].size * sizeof (uint16))) {
uptr->flags = (uptr->flags & ~UNIT_DTYPE) | (i << UNIT_V_DTYPE);
uptr->capac = drv_tab[i].size;
return SCPE_OK;
}
}
return SCPE_OK;
}
/* Device detach */
t_stat ds_detach (UNIT *uptr)
{
if (!(uptr->flags & UNIT_ATT)) return SCPE_OK; /* attached? */
ds_load_unload (uptr, UNIT_UNLOAD, NULL, NULL); /* unload heads */
return detach_unit (uptr);
}
/* Load and unload heads */
t_stat ds_load_unload (UNIT *uptr, int32 value, char *cptr, void *desc)
{
if ((uptr->flags & UNIT_ATT) == 0) return SCPE_UNATT; /* must be attached to [un]load */
if (value == UNIT_UNLOAD) { /* unload heads? */
uptr->flags = uptr->flags | UNIT_UNLOAD; /* indicate unload */
uptr->STA = DS2_ATN; /* update drive status */
ds_sched_atn (uptr); /* schedule attention */
}
else { /* load heads */
uptr->flags = uptr->flags & ~UNIT_UNLOAD; /* indicate load */
uptr->STA = DS2_ATN | DS2_FS; /* update drive status */
}
return SCPE_OK;
}
/* Schedule attention interrupt if CTL set, not restore, and controller idle */
void ds_sched_atn (UNIT *uptr)
{
int32 i;
if (!ds_dib.ctl || (sim_switches & SIM_SW_REST)) return;
for (i = 0; i < (DS_NUMDR + 1); i++) { /* check units, ctrl */
if (sim_is_active (ds_dev.units + i)) return;
}
uptr->FNC = DSC_ATN; /* pseudo operation */
sim_activate (uptr, 1); /* do immediately */
return;
}
/* Set size command validation routine */
t_stat ds_set_size (UNIT *uptr, int32 val, char *cptr, void *desc)
{
if (uptr->flags & UNIT_ATT) return SCPE_ALATT;
uptr->capac = drv_tab[GET_DTYPE (val)].size;
return SCPE_OK;
}
/* 13037 bootstrap routine (HP 12992B ROM) */
const uint16 ds_rom[IBL_LNT] = {
0017727, /* STRT JSB STAT ; get status */
0002021, /* SSA,RSS ; is drive ready? */
0027742, /* JMP DMA ; yes, set up DMA */
0013714, /* AND B20 ; no, check status bits */
0002002, /* SZA ; faulty or hard down? */
0102030, /* HLT 30B ; HALT 30B */
0027700, /* JMP STRT ; try again */
0102011, /* ADR1 OCT 102011 */
0102055, /* ADR2 OCT 102055 */
0164000, /* CNT DEC -6144 */
0000007, /* D7 OCT 7 */
0001400, /* STCM OCT 1400 */
0000020, /* B20 OCT 20 */
0017400, /* STMS OCT 17400 */
0000000, /* 9 NOP's */
0000000,
0000000,
0000000,
0000000,
0000000,
0000000,
0000000,
0000000,
0000000, /* STAT NOP ; status check routine */
0107710, /* CLC DC,C ; set command mode */
0063713, /* LDA STCM ; get status command */
0102610, /* OTA DC ; output status command */
0102310, /* SFS DC ; wait for stat#1 word */
0027733, /* JMP *-1 */
0107510, /* LIB DC,C ; B-reg - status#1 word */
0102310, /* SFS DC ; wait for stat#2 word */
0027736, /* JMP *-1 */
0103510, /* LIA DC,C ; A-reg - status#2 word */
0127727, /* JMP STAT,I ; return */
0067776, /* DMA LDB DMAC ; get DMA control word */
0106606, /* OTB 6 ; output DMA ctrl word */
0067707, /* LDB ADR1 ; get memory address */
0106702, /* CLC 2 ; set memory addr mode */
0106602, /* OTB 2 ; output mem addr to DMA */
0102702, /* STC 2 ; set word count mode */
0067711, /* LDB CNT ; get word count */
0106602, /* OTB 2 ; output word cnt to DMA */
0106710, /* CLC CLC DC ; set command follows */
0102501, /* LIA 1 ; load switches */
0106501, /* LIB 1 ; register settings */
0013712, /* AND D7 ; isolate head number */
0005750, /* BLF,CLE,SLB ; bit 12 = 0? */
0027762, /* JMP *+3 ; no, manual boot */
0002002, /* SZA ; yes, RPL, head# = 0? */
0001000, /* ALS ; no, head# = 1 --> 2 */
0001720, /* ALF,ALS ; form cold load */
0001000, /* ALS ; command word */
0103706, /* STC 6,C ; activate DMA */
0103610, /* OTA DC,C ; output cold load cmd */
0102310, /* SFS DC ; is cold load done? */
0027766, /* JMP *-1 ; no, wait */
0017727, /* JSB STAT ; yes, get status */
0060001, /* LDA 1 ; get status word #1 */
0013715, /* AND STMS ; isolate status bits */
0002002, /* SZA ; is transfer ok? */
0027700, /* JMP STRT ; no, try again */
0117710, /* JSB ADR2,I ; yes, start program */
0000010, /* DMAC ABS DC ; DMA command word */
0170100, /* ABS -STRT */
};
t_stat ds_boot (int32 unitno, DEVICE *dptr)
{
int32 dev;
if (unitno != 0) return SCPE_NOFNC; /* only unit 0 */
dev = ds_dib.devno; /* get data chan dev */
if (ibl_copy (ds_rom, dev)) return SCPE_IERR; /* copy boot to memory */
SR = (SR & (IBL_OPT | IBL_DS_HEAD)) | IBL_DS | IBL_MAN | (dev << IBL_V_DEV);
return SCPE_OK;
}