Rivoreo Source Code Repositories
src.rivoreo.one / emulators / simh / 1a68c7d900d20e302f3229e45cc32daedb7059ef / . / 3B2 / 3b2_iu.c
blob: 5511dd8179312b2b0f4249f0098a9a350bcf245b [file] [log] [blame] [raw]
/* 3b2_iu.c: SCN2681A Dual UART Implementation
Copyright (c) 2017, Seth J. Morabito
Permission is hereby granted, free of charge, to any person
obtaining a copy of this software and associated documentation
files (the "Software"), to deal in the Software without
restriction, including without limitation the rights to use, copy,
modify, merge, publish, distribute, sublicense, and/or sell copies
of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be
included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Except as contained in this notice, the name of the author shall
not be used in advertising or otherwise to promote the sale, use or
other dealings in this Software without prior written authorization
from the author.
*/
#include "3b2_iu.h"
#include "sim_tmxr.h"
/*
* The 3B2/400 has two on-board serial ports, labeled CONSOLE and
* CONTTY. The CONSOLE port is (naturally) the system console. The
* CONTTY port serves as a secondary serial port for an additional
* terminal.
*
* These lines are driven by an SCN2681A Dual UART, with two receivers
* and two transmitters.
*
* In addition to the two TX/RX ports, the SCN27681A also has one
* programmable timer.
*
* The SCN2681A UART is represented here by four devices:
*
* - Console TTI (Input, port A)
* - Console TTO (Output, port A)
* - Contty (I/O, port B. Terminal multiplexer with one line)
* - IU Timer
*/
/*
* Registers
*/
/* The IU state shared between A and B */
IU_STATE iu_state;
/* The tx/rx state for ports A and B */
IU_PORT iu_console;
IU_PORT iu_contty;
/* The timer state */
IU_TIMER_STATE iu_timer_state;
/* Flags for incrementing mode pointers */
t_bool iu_increment_a = FALSE;
t_bool iu_increment_b = FALSE;
extern uint16 csr_data;
BITFIELD sr_bits[] = {
BIT(RXRDY),
BIT(FFULL),
BIT(TXRDY),
BIT(TXEMT),
BIT(OVRN_E),
BIT(PRTY_E),
BIT(FRM_E),
BIT(BRK),
ENDBITS
};
BITFIELD isr_bits[] = {
BIT(TXRDYA),
BIT(RXRDY_FFA),
BIT(DLTA_BRKA),
BIT(CTR_RDY),
BIT(TXRDYB),
BIT(RXRDY_FFB),
BIT(DLTA_BRKB),
BIT(IPC),
ENDBITS
};
BITFIELD acr_bits[] = {
BIT(BRG_SET),
BITFFMT(TMR_MODE,3,%d),
BIT(DLTA_IP3),
BIT(DLTA_IP2),
BIT(DLTA_IP1),
BIT(DLTA_IP0),
ENDBITS
};
BITFIELD conf_bits[] = {
BIT(TX_EN),
BIT(RX_EN),
ENDBITS
};
/* TTI (Console) data structures */
REG tti_reg[] = {
{ HRDATADF(STAT, iu_console.stat, 8, "Status", sr_bits) },
{ HRDATADF(CONF, iu_console.conf, 8, "Config", conf_bits) },
{ BRDATAD(DATA, iu_console.rxbuf, 16, 8, IU_BUF_SIZE, "Data") },
{ NULL }
};
UNIT tti_unit = { UDATA(&iu_svc_tti, UNIT_IDLE, 0), TMLN_SPD_19200_BPS };
DEVICE tti_dev = {
"TTI", &tti_unit, tti_reg, NULL,
1, 8, 32, 1, 8, 8,
NULL, NULL, &tti_reset,
NULL, NULL, NULL, NULL,
DEV_DEBUG, 0, sys_deb_tab
};
/* TTO (Console) data structures */
REG tto_reg[] = {
{ HRDATADF(STAT, iu_console.stat, 8, "Status", sr_bits) },
{ HRDATADF(ISTAT, iu_state.istat, 8, "Interrupt Status", isr_bits) },
{ HRDATAD(IMR, iu_state.imr, 8, "Interrupt Mask") },
{ HRDATADF(ACR, iu_state.acr, 8, "Auxiliary Control Register", acr_bits) },
{ HRDATAD(DATA, iu_console.txbuf, 8, "Data") },
{ NULL }
};
UNIT tto_unit = { UDATA(&iu_svc_tto, TT_MODE_8B, 0), SERIAL_OUT_WAIT };
DEVICE tto_dev = {
"TTO", &tto_unit, tto_reg, NULL,
1, 8, 32, 1, 8, 8,
NULL, NULL, NULL,
NULL, NULL, NULL, NULL,
DEV_DEBUG, 0, sys_deb_tab
};
/* CONTTY data structures */
/*
* The CONTTY "multiplexer" is a bit unusual in that it serves only a
* single line, representing the built-in CONTTY port. On a real
* 3B2/400, the system board's dual UART serves both CONSOLE and
* CONTTY lines, giving support for two terminals. In the simulator,
* the CONSOLE is served by TTI and TTO devices, whereas the CONTTY is
* served by a TMXR multiplexer.
*/
TMLN *contty_ldsc = NULL;
TMXR contty_desc = { 1, 0, 0, NULL };
REG contty_reg[] = {
{ HRDATADF(STAT, iu_contty.stat, 8, "Status", sr_bits) },
{ HRDATADF(CONF, iu_contty.conf, 8, "Config", conf_bits) },
{ BRDATAD(RXDATA, iu_contty.rxbuf, 16, 8, IU_BUF_SIZE, "RX Data") },
{ HRDATAD(TXDATA, iu_contty.txbuf, 8, "TX Data") },
{ HRDATADF(ISTAT, iu_state.istat, 8, "Interrupt Status", isr_bits) },
{ HRDATAD(IMR, iu_state.imr, 8, "Interrupt Mask") },
{ HRDATADF(ACR, iu_state.acr, 8, "Auxiliary Control Register", acr_bits) },
{ NULL }
};
char *brg_rates[IU_SPEED_REGS][IU_SPEEDS] = {
{NULL, "110", NULL, NULL,
"300", NULL, NULL, "1200",
"2400", "4800", NULL, "9600",
"38400", NULL, NULL, NULL},
{NULL, "110", NULL, NULL,
"300", NULL, "1200", NULL,
NULL, "2400", "4800", "9600",
"19200", NULL, NULL, NULL}
};
char *parity[3] = {"O", "E", "N"};
UNIT contty_unit[2] = {
{ UDATA(&iu_svc_contty_rcv, UNIT_ATTABLE, 0) },
{ UDATA(&iu_svc_contty_xmt, TT_MODE_8B, 0), SERIAL_OUT_WAIT }
};
UNIT *contty_rcv_unit = &contty_unit[0];
UNIT *contty_xmt_unit = &contty_unit[1];
DEVICE contty_dev = {
"CONTTY", contty_unit, contty_reg, NULL,
1, 8, 32, 1, 8, 8,
&tmxr_ex, &tmxr_dep, &contty_reset,
NULL, &contty_attach, &contty_detach,
NULL, DEV_DISABLE|DEV_DEBUG|DEV_MUX,
0, sys_deb_tab, NULL, NULL,
NULL, NULL,
(void *)&contty_desc,
NULL
};
/* IU Timer data structures */
REG iu_timer_reg[] = {
{ HRDATAD(CTR_SET, iu_timer_state.c_set, 16, "Counter Setting") },
{ NULL }
};
UNIT iu_timer_unit = { UDATA(&iu_svc_timer, 0, 0) };
DEVICE iu_timer_dev = {
"IUTIMER", &iu_timer_unit, iu_timer_reg, NULL,
1, 8, 32, 1, 8, 8,
NULL, NULL, &iu_timer_reset,
NULL, NULL, NULL, NULL,
DEV_DEBUG, 0, sys_deb_tab
};
uint8 brg_reg = 0; /* Selected baud-rate generator register */
uint8 brg_clk = 11; /* Selected baud-rate generator clock */
uint8 parity_sel = 1; /* Selected parity */
uint8 bits_per_char = 7;
t_stat contty_attach(UNIT *uptr, CONST char *cptr)
{
t_stat r = tmxr_attach(&contty_desc, uptr, cptr);
TMLN *lp;
if (r != SCPE_OK) {
tmxr_clear_modem_control_passthru(&contty_desc);
return r;
}
lp = &contty_ldsc[0];
tmxr_set_get_modem_bits(lp, TMXR_MDM_DTR|TMXR_MDM_RTS, 0, NULL);
return SCPE_OK;
}
t_stat contty_detach(UNIT *uptr)
{
t_stat r = tmxr_detach(&contty_desc, uptr);
tmxr_clear_modem_control_passthru(&contty_desc);
return r;
}
void increment_modep_a()
{
iu_increment_a = FALSE;
iu_console.modep++;
if (iu_console.modep > 1) {
iu_console.modep = 0;
}
}
void increment_modep_b()
{
iu_increment_b = FALSE;
iu_contty.modep++;
if (iu_contty.modep > 1) {
iu_contty.modep = 0;
}
}
void iu_txrdy_a_irq() {
if ((iu_state.imr & IMR_TXRA) &&
(iu_console.conf & TX_EN) &&
(iu_console.stat & STS_TXR)) {
csr_data |= CSRUART;
}
}
void iu_txrdy_b_irq() {
if ((iu_state.imr & IMR_TXRB) &&
(iu_contty.conf & TX_EN) &&
(iu_contty.stat & STS_TXR)) {
csr_data |= CSRUART;
}
}
t_stat tti_reset(DEVICE *dptr)
{
memset(&iu_state, 0, sizeof(IU_STATE));
memset(&iu_console, 0, sizeof(IU_PORT));
tmxr_set_console_units(&tti_unit, &tto_unit);
/* Input Port logic is inverted - 0 means set */
iu_state.inprt = ~(IU_DCDA);
/* Start the Console TTI polling loop */
if (!sim_is_active(&tti_unit)) {
sim_activate(&tti_unit, tti_unit.wait);
}
return SCPE_OK;
}
t_stat contty_reset(DEVICE *dtpr)
{
char line_config[16];
if (contty_ldsc == NULL) {
contty_desc.ldsc =
contty_ldsc =
(TMLN *)calloc(1, sizeof(*contty_ldsc));
}
memset(&iu_state, 0, sizeof(IU_STATE));
memset(&iu_contty, 0, sizeof(IU_PORT));
brg_reg = 0;
brg_clk = BRG_DEFAULT;
parity_sel = IU_PARITY_EVEN;
bits_per_char = 7;
sprintf(line_config, "%s-%d%s1",
brg_rates[brg_reg][brg_clk],
bits_per_char,
parity[parity_sel]);
tmxr_set_config_line(&contty_ldsc[0], line_config);
/* Start the CONTTY polling loop */
if (!sim_is_active(contty_rcv_unit)) {
sim_activate(contty_rcv_unit, contty_rcv_unit->wait);
}
return SCPE_OK;
}
t_stat iu_timer_reset(DEVICE *dptr)
{
memset(&iu_timer_state, 0, sizeof(IU_TIMER_STATE));
return SCPE_OK;
}
/* Service routines */
t_stat iu_svc_tti(UNIT *uptr)
{
int32 temp;
sim_clock_coschedule(uptr, tmxr_poll);
/* TODO:
- If there has been a change on IP0-IP3, set the corresponding
bits in IPCR, if configured to do so. We'll need to figure out
how these are wired (DCD pin, etc?)
- Update the Output Port pins (which are logically inverted)
based on the contents of the OPR, OPCR, MR, and CR registers.
*/
if ((temp = sim_poll_kbd()) < SCPE_KFLAG) {
return temp;
}
if (iu_console.conf & RX_EN) {
if ((iu_console.stat & STS_FFL) == 0) {
iu_console.rxbuf[iu_console.w_p] = (temp & 0xff);
iu_console.w_p = (iu_console.w_p + 1) % IU_BUF_SIZE;
if (iu_console.w_p == iu_contty.w_p) {
iu_console.stat |= STS_FFL;
}
}
iu_console.stat |= STS_RXR;
iu_state.istat |= ISTS_RAI;
if (iu_state.imr & IMR_RXRA) {
csr_data |= CSRUART;
}
}
return SCPE_OK;
}
t_stat iu_svc_tto(UNIT *uptr)
{
iu_txrdy_a_irq();
return SCPE_OK;
}
t_stat iu_svc_contty_rcv(UNIT *uptr)
{
int32 temp, ln;
if ((uptr->flags & UNIT_ATT) == 0) {
return SCPE_OK;
}
ln = tmxr_poll_conn(&contty_desc);
if (ln >= 0) {
contty_ldsc[ln].rcve = 1;
/* Set DCD */
iu_state.inprt &= ~(IU_DCDB);
iu_state.ipcr |= IU_DCDB;
/* Cause an interrupt */
csr_data |= CSRUART;
}
tmxr_poll_rx(&contty_desc);
if (contty_ldsc[0].conn) {
temp = tmxr_getc_ln(&contty_ldsc[0]);
if (temp && !(temp & SCPE_BREAK)) {
if (iu_contty.conf & RX_EN) {
if ((iu_contty.stat & STS_FFL) == 0) {
iu_contty.rxbuf[iu_contty.w_p] = (temp & 0xff);
iu_contty.w_p = (iu_contty.w_p + 1) % IU_BUF_SIZE;
if (iu_contty.w_p == iu_contty.r_p) {
iu_contty.stat |= STS_FFL;
}
}
iu_contty.stat |= STS_RXR;
iu_state.istat |= ISTS_RBI;
if (iu_state.imr & IMR_RXRB) {
csr_data |= CSRUART;
}
}
}
}
tmxr_clock_coschedule(uptr, tmxr_poll);
return SCPE_OK;
}
t_stat iu_svc_contty_xmt(UNIT *uptr)
{
tmxr_poll_tx(&contty_desc);
iu_txrdy_b_irq();
return SCPE_OK;
}
t_stat iu_svc_timer(UNIT *uptr)
{
iu_state.istat |= ISTS_CRI;
if (iu_state.imr & IMR_CTR) {
csr_data |= CSRUART;
}
return SCPE_OK;
}
/*
* Reg | Name (Read) | Name (Write)
* -----+-------------------------+----------------------------
* 0 | Mode Register 1/2 A | Mode Register 1/2 A
* 1 | Status Register A | Clock Select Register A
* 2 | BRG Test | Command Register A
* 3 | Rx Holding Register A | Tx Holding Register A
* 4 | Input Port Change Reg. | Aux. Control Register
* 5 | Interrupt Status Reg. | Interrupt Mask Register
* 6 | Counter/Timer Upper Val | C/T Upper Preset Val.
* 7 | Counter/Timer Lower Val | C/T Lower Preset Val.
* 8 | Mode Register B | Mode Register B
* 9 | Status Register B | Clock Select Register B
* 10 | 1X/16X Test | Command Register B
* 11 | Rx Holding Register B | Tx Holding Register B
* 12 | *Reserved* | *Reserved*
* 13 | Input Ports IP0 to IP6 | Output Port Conf. Reg.
* 14 | Start Counter Command | Set Output Port Bits Cmd.
* 15 | Stop Counter Command | Reset Output Port Bits Cmd.
*/
uint32 iu_read(uint32 pa, size_t size)
{
uint8 reg, modep;
uint32 data, delay;
reg = (uint8) (pa - IUBASE);
switch (reg) {
case MR12A:
modep = iu_console.modep;
data = iu_console.mode[modep];
iu_increment_a = TRUE;
break;
case SRA:
data = iu_console.stat;
break;
case RHRA:
data = iu_console.rxbuf[iu_console.r_p];
iu_console.r_p = (iu_console.r_p + 1) % IU_BUF_SIZE;
iu_console.stat &= ~(STS_RXR|STS_FFL);
iu_state.istat &= ~ISTS_RAI;
csr_data &= ~CSRUART;
break;
case IPCR:
data = iu_state.ipcr;
/* Reading the port resets it */
iu_state.ipcr = 0;
csr_data &= ~CSRUART;
break;
case ISR:
data = iu_state.istat;
break;
case CTU:
data = (iu_timer_state.c_set >> 8) & 0xff;
break;
case CTL:
data = iu_timer_state.c_set & 0xff;
break;
case MR12B:
modep = iu_contty.modep;
data = iu_contty.mode[modep];
iu_increment_b = TRUE;
break;
case SRB:
data = iu_contty.stat;
break;
case RHRB:
data = iu_contty.rxbuf[iu_contty.r_p];
iu_contty.r_p = (iu_contty.r_p + 1) % IU_BUF_SIZE;
/* If the FIFO is not empty, we must cause another interrupt
* to continue reading */
if (iu_contty.r_p == iu_contty.w_p) {
iu_contty.stat &= ~(STS_RXR|STS_FFL);
iu_state.istat &= ~ISTS_RBI;
} else {
csr_data |= CSRUART;
}
break;
case INPRT:
data = iu_state.inprt;
break;
case START_CTR:
data = 0;
iu_state.istat &= ~ISTS_CRI;
delay = (uint32) (IU_TIMER_STP * iu_timer_state.c_set);
sim_activate_abs(&iu_timer_unit, (int32) DELAY_US(delay));
break;
case STOP_CTR:
data = 0;
iu_state.istat &= ~ISTS_CRI;
csr_data &= ~CSRUART;
sim_cancel(&iu_timer_unit);
break;
case 17: /* Clear DMAC interrupt */
data = 0;
iu_console.drq = FALSE;
iu_contty.drq = FALSE;
csr_data &= ~CSRDMA;
break;
default:
data = 0;
break;
}
return data;
}
void iu_write(uint32 pa, uint32 val, size_t size)
{
uint8 reg;
uint8 modep;
uint8 bval = (uint8) val;
char line_config[16];
reg = (uint8) (pa - IUBASE);
switch (reg) {
case MR12A:
modep = iu_console.modep;
iu_console.mode[modep] = bval;
iu_increment_a = TRUE;
break;
case CSRA:
/* Set baud rate - not yet implemented on console */
break;
case CRA: /* Command A */
iu_w_cmd(PORT_A, bval);
break;
case THRA: /* TX/RX Buf A */
/* Loopback mode */
if ((iu_console.mode[1] & 0xc0) == 0x80) {
iu_console.txbuf = bval;
/* This is also a Receive */
if ((iu_console.stat & STS_FFL) == 0) {
iu_console.rxbuf[iu_console.w_p] = bval;
iu_console.w_p = (iu_console.w_p + 1) % IU_BUF_SIZE;
if (iu_console.w_p == iu_console.r_p) {
iu_console.stat |= STS_FFL;
}
}
iu_console.stat |= STS_RXR;
iu_state.istat |= ISTS_RAI;
if (iu_state.imr & IMR_RXRA) {
csr_data |= CSRUART;
}
} else {
iu_tx(PORT_A, bval);
}
csr_data &= ~CSRUART;
break;
case ACR: /* Auxiliary Control Register */
iu_state.acr = bval;
brg_reg = (bval >> 7) & 1;
break;
case IMR:
iu_state.imr = bval;
csr_data &= ~CSRUART;
/* Possibly cause an interrupt */
iu_txrdy_a_irq();
iu_txrdy_b_irq();
break;
case CTUR: /* Counter/Timer Upper Preset Value */
/* Clear out high byte */
iu_timer_state.c_set &= 0x00ff;
/* Set high byte */
iu_timer_state.c_set |= ((uint16) bval << 8);
break;
case CTLR: /* Counter/Timer Lower Preset Value */
/* Clear out low byte */
iu_timer_state.c_set &= 0xff00;
/* Set low byte */
iu_timer_state.c_set |= bval;
break;
case MR12B:
modep = iu_contty.modep;
iu_contty.mode[modep] = bval;
iu_increment_b = TRUE;
if (modep == 0) {
if ((bval >> 4) & 1) {
/* No parity */
parity_sel = IU_PARITY_NONE;
} else {
/* Parity enabled */
if (bval & 4) {
parity_sel = IU_PARITY_ODD;
} else {
parity_sel = IU_PARITY_EVEN;
}
}
bits_per_char = (bval & 3) + 5;
}
break;
case CRB: /* Command B */
iu_w_cmd(PORT_B, bval);
break;
case CSRB:
brg_clk = (bval >> 4) & 0xf;
if (brg_rates[brg_reg][brg_clk] != NULL) {
sprintf(line_config, "%s-%d%s1",
brg_rates[brg_reg][brg_clk],
bits_per_char,
parity[parity_sel]);
sim_debug(EXECUTE_MSG, &contty_dev,
"Setting CONTTY line to %s\n",
line_config);
tmxr_set_config_line(&contty_ldsc[0], line_config);
}
break;
case THRB: /* TX/RX Buf B */
/* Loopback mode */
if ((iu_contty.mode[1] & 0xc0) == 0x80) {
iu_contty.txbuf = bval;
/* This is also a Receive */
if ((iu_contty.stat & STS_FFL) == 0) {
iu_contty.rxbuf[iu_contty.w_p] = bval;
iu_contty.w_p = (iu_contty.w_p + 1) % IU_BUF_SIZE;
if (iu_contty.w_p == iu_contty.r_p) {
iu_contty.stat |= STS_FFL;
}
}
iu_contty.stat |= STS_RXR;
iu_state.istat |= ISTS_RBI;
if (iu_state.imr & IMR_RXRB) {
csr_data |= CSRUART;
}
} else {
iu_tx(PORT_B, bval);
}
break;
case OPCR:
iu_state.opcr = bval;
break;
case SOPR:
/* Bit 2 of the IU output register is used as a soft power
* switch. When set, the machine will power down
* immediately. */
if (bval & IU_KILLPWR) {
stop_reason = STOP_POWER;
}
break;
case ROPR:
break;
default:
break;
}
}
void iua_drq_handled()
{
csr_data |= CSRDMA;
}
void iub_drq_handled()
{
csr_data |= CSRDMA;
}
static SIM_INLINE void iu_tx(uint8 portno, uint8 val)
{
IU_PORT *p;
UNIT *uptr;
TMLN *lp;
if (portno == 0) {
p = &iu_console;
uptr = &tto_unit;
} else {
p = &iu_contty;
uptr = contty_xmt_unit;
}
p->txbuf = val;
if (p->conf & TX_EN) {
p->stat &= ~(STS_TXR|STS_TXE);
iu_state.istat &= ~(1 << (portno*4));
if (portno == PORT_A) {
/* Write the character to the SIMH console */
sim_putchar(val);
} else {
lp = &contty_ldsc[0];
tmxr_putc_ln(lp, val);
}
/* The buffer is now empty, we've transmitted, so set TXR */
p->stat |= STS_TXR;
iu_state.istat |= (1 << (portno*4));
/* Possibly cause an interrupt */
sim_activate_abs(uptr, uptr->wait);
}
}
static SIM_INLINE void iu_w_cmd(uint8 portno, uint8 cmd)
{
IU_PORT *p;
if (portno == 0) {
p = &iu_console;
} else {
p = &iu_contty;
}
/* Enable or disable transmitter */
/* Disable always wins, if both are set */
if (cmd & CMD_DTX) {
p->conf &= ~TX_EN;
p->stat &= ~STS_TXR;
p->stat &= ~STS_TXE;
p->drq = FALSE;
} else if (cmd & CMD_ETX) {
p->conf |= TX_EN;
/* TXE and TXR are always set by an ENABLE */
p->stat |= STS_TXR;
p->stat |= STS_TXE;
p->drq = TRUE;
iu_state.istat |= 1 << (portno*4);
if (portno == 0) {
iu_txrdy_a_irq();
} else {
iu_txrdy_b_irq();
}
}
/* Enable or disable receiver. */
/* Disable always wins, if both are set */
if (cmd & CMD_DRX) {
p->conf &= ~RX_EN;
p->stat &= ~STS_RXR;
} else if (cmd & CMD_ERX) {
p->conf |= RX_EN;
}
/* Command register bits 6-4 have special meaning */
switch ((cmd >> CMD_MISC_SHIFT) & CMD_MISC_MASK) {
case 1:
/* Causes the Channel A MR pointer to point to MR1. */
p->modep = 0;
break;
case 2:
/* Reset receiver. Resets the Channel's receiver as if a
hardware reset had been applied. The receiver is disabled
and the FIFO is flushed. */
p->stat &= ~STS_RXR;
p->conf &= ~RX_EN;
p->w_p = 0;
p->r_p = 0;
break;
case 3:
/* Reset transmitter. Resets the Channel's transmitter as if a
hardware reset had been applied. */
p->stat &= ~STS_TXR;
p->stat &= ~STS_TXE;
p->conf &= ~TX_EN;
p->w_p = 0;
p->r_p = 0;
break;
case 4:
/* Reset error status. Clears the Channel's Received Break,
Parity Error, and Overrun Error bits in the status register
(SRA[7:4]). Used in character mode to clear OE status
(although RB, PE and FE bits will also be cleared) and in
block mode to clear all error status after a block of data
has been received. */
p->stat &= ~(STS_FER|STS_PER|STS_OER);
break;
case 5:
/* Reset Channel's break change interrupt. Causes the Channel
A break detect change bit in the interrupt status register
(ISR[2] for Chan. A, ISR[6] for Chan. B) to be cleared to
zero. */
iu_state.istat &= ~(1 << (2 + portno*4));
break;
case 6:
/* Start break. Forces the TxDA output LOW (spacing). If the
transmitter is empty the start of the break condition will
be delayed up to two bit times. If the transmitter is
active the break begins when transmission of the character
is completed. If a character is in the THR, the start of
the break will be delayed until that character, or any
other loaded subsequently are transmitted. The transmitter
must be enabled for this command to be accepted. */
/* Not Implemented */
break;
case 7:
/* Stop break. The TxDA line will go HIGH (marking) within two
bit times. TxDA will remain HIGH for one bit time before
the next character, if any, is transmitted. */
/* Not Implemented */
break;
}
}